The SP805 DT binding requires two clocks to be specified, but the
Broadcom Cygnus DT currently only specifies one clock.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux and U-Boot SP805 driver would use the first clock
to derive the actual watchdog counter frequency.
Since currently both are the very same clock, we can just double the
clock reference, and add the correct clock-names, to match the binding.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
add support for the Cisco Meraki MR32.
This is a dual-band enterprise class 802.11ac access point.
The unit was donated by Chris Blake. Thank you!
SoC: Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM: 128 MiB
NAND: 128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH: 1GBit Ethernet Port - PoE
WIFI1: Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2: Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3: Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BLE: Broadcom BCM20732 (ttyS1)
LEDS: 1 x Programmable RGB Status LED (driven by a PWM)
1 x White LED (GPIO)
1 x Orange LED Fault Indicator (GPIO)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC)
ina219 hardware monitor (i2c)
Kensington Lock
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC, RX, TX, GND.
Odd stuff:
- uart0 clock frequency is 62.5 MHz.
- The LEDs are labeled as SYS-LED1 through SYS-LED3
because of the silkscreen on the PCB.
- the original u-boot has been compiled with most functions
and commands disabled. The u-boot env isn't setup properly
either and as a result, the bcm47xxpart probing is not
working. Hence, the nand partitions are specified through a
"fixed-partition" binding.
- The "WICED SMART(TM)" Bluetooth LE 4.0 BCM20732 chip is
connected to uart2 of the SoC. The BCM20732 does not
provide a HCI. So the linux' bluetooth stack is useless.
The mock-up node with the compatible binding and
enable-gpios property is provided solely as documentation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Documentation/devicetree/bindings/net/dsa/dsa.txt says that the phy-mode
property should be specified on port nodes. However, the microchip
drivers read it from the switch node.
Let the driver use the per-port property and fall back to the old
location with a warning.
Fix in-tree users.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Link: https://lore.kernel.org/netdev/20200617082235.GA1523@laureti-dev/
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SPI NOR device which is connected to MSIOF0 interface
on the iWave RainboW-G21d-q7 board.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200907155541.2011-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All dra7/am57 boards converted to use new driver, so drop legacy
cpsw dt node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch CompuLab CL-SOM-AM57x board to use new cpsw switch driver. Those
board configured in dual_mac mode by default. Hence, dual_mac mode has been
preserved the same way between legacy and new driver it's safe to switch
drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all TI DRA7x boards to use new cpsw switch driver. Those boards
configured in dual_mac mode by default. Hence, dual_mac mode has been
preserved the same way between legacy and new driver it's safe to switch
drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all TI AM5728 BeagleBoard-X15 boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all am571/2/4-idk boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch BeagleBone AI to use new cpsw switch driver.
It has one Ext. port only and fits dual_mac mode with no issues.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove nokia,nvm-size property as it is no longer needed. The driver can
nowadays figure out the size so do not specify it in DT.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 1c8f406507 ("ARM: dts: BCM5301X: convert to iProc QSPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 329f98c197 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
spi-gpio-0: $nodename:0: 'spi-gpio-0' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-25-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-16-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-15-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-14-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-13-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-12-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-11-krzk@kernel.org
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-9-krzk@kernel.org
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-8-krzk@kernel.org
The fixed clocks are kept under dedicated 'external-clocks' node, thus a
fake 'reg' was added. This is not correct with dtschema as fixed-clock
binding does not have a 'reg' property. Moving fixed clocks out of
'soc' to root node fixes multiple dtbs_check warnings:
external-clocks: $nodename:0: 'external-clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
external-clocks: #size-cells:0:0: 0 is not one of [1, 2]
external-clocks: oscillator@0:reg:0: [0] is too short
external-clocks: oscillator@1:reg:0: [1] is too short
external-clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-7-krzk@kernel.org
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-6-krzk@kernel.org
Fix typo in pinctrl property of "vibrator-en" fixed regulator in Aries
family of boards. The error caused lack of pin configuration for the
GPIO used in vibrator.
Fixes: 04568cb58a ("ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-5-krzk@kernel.org
GPU needs additional regulator, add it to devicetree of bpi-r2
Signed-off-by: Alex Ryabchenko <d3adme4t@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200904110002.88966-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
mt7623a has no graphics support so move nodes from generic mt7623.dtsi
to mt7623n.dtsi
Fixes: 1f6ed22459 ("arm: dts: mt7623: add Mali-450 device node")
Suggested-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200904110002.88966-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
A feature was added to the aspeed vuart driver to configure the vuart
interrupt (sirq) polarity according to the LPC/eSPI strapping register.
Systems that depend on a active low behaviour (sirq_polarity set to 0)
such as OpenPower boxes also use LPC, so this relationship does not
hold. Jeremy confirms that the s2600st which is strapped for eSPI also
does not have this relationship.
The property was added for a Tyan S7106 system which is not supported
in the kernel tree. Should this or other systems wish to use this
feature of the driver they should add it to the machine specific device
tree.
Fixes: c791fc76bc ("arm: dts: aspeed: Add vuart aspeed,sirq-polarity-sense...")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jeremy Kerr <jk@ozlabs.org>
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200812112400.2406734-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 7 to multi-master mode and add the panel device that will
register as a slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200908200101.64974-6-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 0 to multi-master mode and add the panel device that will
register as a slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200908200101.64974-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Now that all the drivers have been adjusted for it, let's bring in the
necessary device tree changes.
The VEC and PV3 are left out for now, since it will require a more specific
clock setup.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/cfce2276d172d3d9c4d34d966b58fd47f77c4e46.1599120059.git-series.maxime@cerno.tech
Add the reg property to each channel node. This update is
to accommodate the multicolor framework. In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200812195020.13568-7-dmurphy@ti.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SP805 binding sets the name for the actual watchdog clock to
"wdog_clk" (with an underscore).
Change the name in the DTs for ARM Ltd. platforms to match that. The
Linux and U-Boot driver use the *first* clock for this purpose anyway,
so it does not break anything.
For MPS2 we only specify one clock so far, but the binding requires
two clocks to be named.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux and U-Boot SP805 driver would use the first clock
to derive the actual watchdog counter frequency. So since currently both
are the very same clock, we can just double the clock reference, and add
the correct clock-names, to match the binding.
Link: https://lore.kernel.org/r/20200828130602.42203-8-andre.przywara@arm.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SP804 DT nodes for Realview, MPS2 and VExpress were not complying
with the binding: it requires either one or three clocks, but does not
allow exactly two clocks.
Simply duplicate the first clock to satisfy the binding requirement.
For MPS2, we triple the clock, and add the clock-names property, as this
is required by the Linux primecell driver.
Try to make the clock-names more consistent on the way.
Link: https://lore.kernel.org/r/20200828142018.43298-3-andre.przywara@arm.com
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SATA PHY in Exynos5250 SoCs has two interfaces and two device nodes:
1. sata-phy@12170000
2. i2c-9/i2c@38
The first node represents the actual SATA PHY device with phy-cells.
The second represents an additional I2C interface, needed by the driver
to communicate with the SATA PHY device. It is not a PHY-provider in
the terms of dtschema so rename it to silence dtbs_check warning:
arch/arm/boot/dts/exynos5250-arndale.dt.yaml: sata-phy@38: '#phy-cells' is a required property
From schema: lib/python3.6/site-packages/dtschema/schemas/phy/phy-provider.yaml
This second device node is also a property of SoC, not a board so move
it there.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902155733.20271-2-krzk@kernel.org
The property samsung,i2c-slave-addr in I2C9 controller on Exynos5250
Arndale and SMDK5250 boards, is not actually needed. There is only one
master on this bus. It's not clear why this property was added at first
place.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200902155733.20271-1-krzk@kernel.org
