One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix this issue if it is not supported by the firmware.
Fixes: 00f481bd89 ("iwlwifi: mvm: add ctdp operations to debugfs")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support a new version of the beacon template command. This replaces v8
of the command, which was missing the rate code. Also, export rate
decision logic to a separate function.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA. This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.
Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.
The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.
This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there is no value received from BIOS
for cTDP budget, the default should be 2000 mWatt.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the NVM data in a000 devices should be shared
across operation mode.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CT-kill is a thermal-based "RF-kill", which disables the NIC
completely if the temperature gets too high, in order to avoid damage.
Add a debugfs entry to simulate high temperatures, in order to test
CT-kill flows in the driver without having to physically heat the
device up.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.
Fixes: 503ab8c56c ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the module parameter is set to disable the LED, we leave the
initialization routine before setting the LEDS_INIT_COMPLETE
status bit. Therefore, there's no need to check the parameter
again on exit, just the status check is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we start an Rx A-MPDU session, we first get the AddBA
request, then we send an ADD_STA command to the firmware
that will reply with a BAID which is a hardware resource
that tracks the BA session.
This BAID will appear on each and every frame that we get
from the firwmare until the A-MPDU session is torn down.
In the Rx path, we look at this BAID to manage the
reordering buffer.
This flow is inherently racy since the hardware will start
to put the BAID in the frames it receives even if the
firmware hasn't sent the response to the ADD_STA command.
This basically means that the driver can get frames with
a valid BAID that it doesn't know yet.
When that happens, the driver used to WARN.
Fix this by simply not WARN in this case. When the driver
will know abou the BAID, it will initialise the relevant
states and the next frame with a valid BAID will refresh
them.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, if a station is removed just as it is adding a new stream,
the queue in question will remain stopped and no more TX will happen
in this queue, leading to connection failures and other problems.
This is because under DQA, when tx is deferred because a queue needs
to be allocated, the mac queue for that TID is stopped until the new
stream is added. If at this point the station that this stream
belongs to is removed, all the deferred tx frames are purged, but the
mac queue is not restarted. As a result, all following tx on this
queue will not be transmitted.
Fix this by starting the relevant mac queues when the deferred tx
frames are purged.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should free 'wgds.pointer' here as done a few lines above in another
error handling path.
It was allocated within 'acpi_evaluate_object()'.
Fixes: c52030a01ccc ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_add_bcast_sta() and the iwl_mvm_rm_bcast_sta() functions
are only called in P2P flows. Add _p2p_ to the function names to make
this explicit.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to spell out the cases when we can just
use ieee80211_is_bufferable_mmpdu().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the TXQ timer freeze code will not properly handle the
large TVQM queue numbers, warn if we get into that code when
we have TVQM. Also, just to catch this earlier, warn if the
firmware image doesn't support AP_LINK_PS but we're running
on HW using TVQM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing purposes, we may want to disable EBS scans at compile time.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During init, the FW checks whether the FSEQ value matches what it
expects. If it doesn't match, we print a warning to let integrators
clearly know that something is wrong. This can happen if another core
(i.e. not WiFi) has updated the FSEQ version. This notification is
only sent by the FW in production, for development firmwares, an
assertion is triggered instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
If the OTP is empty, the NVM_GET_INFO command returns
with flags' bit(0) on. This means the FW returns the
default values for working with. This is allowed, so
use this returned data.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While waiting for queues to empty,
If txq_id == IWL_MVM_INVALID_QUEUE for all txq_ids,
ret is used uninitialized.
Found by Klocwork.
Fixes: d6d517b773 ("iwlwifi: add wait for tx queue empty")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently support 3 different versions of the beacon template
command and the code does some tricks in order to reuse what is
possible across these versions. But it is a bit complicated to read
and soon there will be one more variation that the driver needs
implement, which would complicate it even further.
Refactor the way we send beacon template commands, which increases the
code size a bit, but makes it much easier to read.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the shared memory command parsing into common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad40 ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.
This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.
On A000 devices series, the IV is always added by the
device.
Fix this.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
