This is necessary so that - if ath10k is the only driver using
dev_coredump*() - the functionality is built into the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove redundant semicolon after switch statement.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYkafBAAoJEG4XJFUm622b0EAH/3mFY0WDfdR/Ych29HX1M/Ao
Bd5gQfKzHS8ANR56qqmxEbpLdBnBa8iNC0IS4RFsWVv6qMoEEOHDLeY5W9XsomWK
i45fQN2XIdjBUOyDXUjsyz006cMe79VzRvFf9gfSekP8i8BCWQzyYC8VKt/F+6Sh
yo9yA4Yv3zA3mA3yRKtxSjLm/6xUXCFVNshKGT0rXc/oEfIN6OnIC1k0p0xw2hhl
GyLN6PSGOqcJc91+IoGOg4TaHzPdWJcWatuxGdQn8gKSDg0+gXaNh9Gtf4H/ojqp
Fwt2Ckk5mgJYk/2TAuFRpRXNMTJznUhp4Tjp2AE7EVM0f5JujUbQuPblOVfLIYk=
=vKKN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified, among others, by device and sybsystem ids.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
To solve the issue QCA uses SMBIOS type 0xF8 to store Board Data File Name
Extension to specify the extension/variant name. The driver will take the
extension suffix into consideration and will load the right (non-default)
board data file if necessary.
If it is unnecessary to use extension board data file, please leave the
SMBIOS field blank and default configuration will be used.
Example:
If a default board data file for a specific board is identified by a string
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310"
then the OEM specific data file, if used, could be identified by variant
suffix:
"bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,
subsystem-device=0310,variant=DE_1AB"
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CORE_CTRL_ADDRESS is offset in register address space, it does not
make sense to OR it to derive the final address. It looks like its
a typo, so fix it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
use dma_zalloc_coherent() instead of dma_alloc_coherent and memset().
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
DIAG_TRANSFER_LIMIT is redefined with same value and comments
just below this entry, remove this duplicate entry.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not clearing the previous tx bit rate status
results in a ambigous tx bit rate reporting to
mac80211/cfg80211, for example the previous bit
rate status would have been marked as legacy rate
, while the current rate would have been an HT/VHT
rate with the tx bit rate flags set and this results
in exporting tx bitrate as legacy rate but with HT/VHT
rate flags set, fix this by clearing the tx bitrate
status for each event. This also fixes the below
warning when we do:
iw dev wlan#N station dump
WARNING: net/wireless/util.c:1222 cfg80211
[<c022f104>] (warn_slowpath_null) from [<bf3b9adc>]
(cfg80211_calculate_bitrate+0x110/0x1f4 [cfg80211])
[<bf3b9adc>] (cfg80211_calculate_bitrate [cfg80211]) from
[<bf3dcd54>] (nl80211_put_sta_rate+0x44/0x1dc [cfg80211])
[<bf3dcd54>] (nl80211_put_sta_rate [cfg80211]) from
[<bf3cbc34>] (nl80211_set_interface+0x724/0xd70 [cfg80211])
[<bf3cbc34>] (nl80211_set_interface [cfg80211]) from
[<bf3d0a18>] (nl80211_dump_station+0xdc/0x100 [cfg80211])
[<bf3d0a18>] (nl80211_dump_station [cfg80211])
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Station pointers are RCU protected so driver must
be extra careful if it tries to store them
internally for later use outside of the RCU
section it obtained it in.
It was possible for station teardown to race with
some htt events. The possible outcome could be a
use-after-free and a crash.
Only peer-flow-control capable firmware was
affected (so hardware-wise qca99x0 and qca4019).
This could be done in sta_state() itself via
explicit synchronize_net() call but there's
already a convenient sta_pre_rcu_remove() op that
can be hooked up to avoid extra rcu stall.
The peer->sta pointer itself can't be set to
NULL/ERR_PTR because it is later used in
sta_state() for extra sanity checks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx legacy rate is reported 10 fold, as below
iw dev wlan#N station dump | grep "tx bitrate"
tx bitrate: 240.0 MBit/s
This is because by mistake we multiply by the hardware reported
rate twice by 10, fix this.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In countries where basic operation of channel 169 is allowed,
this fixes the below WARN_ON_ONCE in Rx and fixes the station
connectivity failure in channel 169 as the packet is dropped
in the driver as the current check limits to channel 165. As of
now all the packets beyond channel 165 is dropped, fix this
by extending the range to channel 169.
Call trace:
drivers/net/wireless/ath/ath10k/wmi.c:1505
ath10k_wmi_event_mgmt_rx+0x278/0x440 [ath10k_core]()
Call Trace:
[<c158f812>] ? printk+0x2d/0x2f
[<c105a182>] warn_slowpath_common+0x72/0xa0
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<c105a1d2>] warn_slowpath_null+0x22/0x30
[<f8b67b58>] ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b0e72b>] ? ath10k_pci_sleep+0x8b/0xb0 [ath10k_pci]
[<f8b6ac63>] ath10k_wmi_10_2_op_rx+0xf3/0x3b0
[<f8b6495e>] ath10k_wmi_process_rx+0x1e/0x60
[<f8b5f077>] ath10k_htc_rx_completion_handler+0x347/0x4d0 [ath10k_core]
[<f8b11dc3>] ? ath10k_ce_completed_recv_next+0x53/0x70 [ath10k_pci]
[<f8b0f921>] ath10k_pci_ce_recv_data+0x171/0x1d0 [ath10k_pci]
[<f8b0ec69>] ? ath10k_pci_write32+0x39/0x80 [ath10k_pci]
[<f8b120bc>] ath10k_ce_per_engine_service+0x5c/0xa0 [ath10k_pci]
[<f8b1215f>] ath10k_ce_per_engine_service_any+0x5f/0x70 [ath10k_pci]
[<c1060dc0>] ? local_bh_enable_ip+0x90/0x90
[<f8b1048b>] ath10k_pci_tasklet+0x1b/0x50 [ath10k_pci]
Fixes: 34c30b0a5e ("ath10k: enable advertising support for channel 169, 5Ghz")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware adds extended peer information to the
firmware's statistics payload. This additional info is
stored as a separate data field and the elements are
stored in their own "peers_extd" list.
These elements can pile up in the same way as the peer
information elements. This is because the
ath10k_wmi_10_4_op_pull_fw_stats() function tries to
pull the same amount (num_peer_stats) for every statistic
data unit.
Fixes: 4a49ae94a4 ("ath10k: fix 10.4 extended peer stats update")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear
R7800. 80+80 is possible, but disabled so far since it seems to contain
glitches like missing vht station flags (this may be firmware or mac80211
related).
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
[kvalo@qca.qualcomm.com: refactoring and fix few warnings]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding VHT160 support to ath10k_peer_assoc_h_phymode() the VHT mode
selection code becomes too complex. Simplify it by refactoring the vht part to
a separate function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplified transmit credit distribution code somewhat.
Since the WMI control service will get assigned all credits
there is no need for having a credit_allocation array in
struct ath10k_htc.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removed tx_credits_per_max_message and tx_credit_size
from struct ath10k_htc_ep since they are not used
anywhere in the code.
They are just written, never read.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYalDTAAoJEG4XJFUm622ba2EH/ivoHG9CvmT6HgNw77odDr6b
Zc7plDi2dd9LIzp3rF/9j8Ietfzpu31Pp9Qz0o1Su/s8RJIlXKVF5UeG5IignnEG
02rv7Z+BGPW7SUNDb0cLa27PMYqUAh8vI39sxYSdQ9NQLIlpMLIxxx5iOZyAK5eV
HBRS0pVlSxbAntb1JgWiN/LjjXe/PdhX3CR/b9b468KAcWB6UWj9nXQxFmz7d3uM
dH3buDTgwaq7K24ZAFc1BsD7rgxprpauXxgIMWCKxRERf64WFfYkYdfdCER+PSPH
maV5Te1KzTJBrQHDOPs1ezVe8gDUhb5YE4BJY9SppZpOE1arucq2g3+3obQUeHE=
=DAVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable advertising support for channel 169, 5Ghz so that
based on the regulatory domain(country code) this channel
shall be active for use. For example in countries like India
this channel shall be available for use with latest regulatory updates
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_mac_tx' does not seems to use the per station table
entry pointer 'sta' (struct ieee80211_sta), hence remove passing
this unused argument
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.
Following is one of the scenario
vdev0 is created as STA and connected: txpower:23
vdev1 is created as P2P_DEVICE for control interface: txpower:0
vdev2 is created as p2p go/gc interface: txpower is 21
So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.
ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
ath10k_pci mac vdev_id 0 txpower 23
... (adding interface)
ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
ath10k_pci mac vdev_id 2 txpower 21
ath10k_pci mac txpower 21
... (removing interface)
ath10k_pci mac vdev 2 delete (remove interface)
ath10k_pci vdev 1 txpower 0
ath10k_pci vdev 0 txpower 23
ath10k_pci mac txpower 23
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:
/sys/class/devcoredump/devcd*/data
As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.
Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Signed-off-by: Arun Khandavalli <akhandav@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: rebase, fixes, improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align it with the cts protection call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:
[00]: 0x05020001 0x000015B3 0x0099ACE2 0x00955B31
[04]: 0x0099ACE2 0x00060730 0x00000004 0x00000000
[08]: 0x0044C754 0x00412C10 0x00000000 0x00409C54
[12]: 0x00000009 0x00000000 0x00952F6C 0x00952F77
[16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
[20]: 0x4099ACE2 0x0040E858 0x00421254 0x004127F4
[24]: 0x8099B9B2 0x0040E8B8 0x00000000 0xC099ACE2
[28]: 0x800B75CB 0x0040E8F8 0x00000007 0x00005008
[32]: 0x809B048A 0x0040E958 0x00000010 0x00433B10
[36]: 0x809AFBBC 0x0040E9A8 0x0042BB74 0x0042BBBC
[40]: 0x8091D252 0x0040E9C8 0x0042BBBC 0x00000001
[44]: 0x809FFA45 0x0040EA78 0x0043D3E4 0x0042C2C8
[48]: 0x809FCEF4 0x0040EA98 0x0043D3E4 0x00000001
[52]: 0x80911210 0x0040EAE8 0x00000010 0x004041D0
[56]: 0x80911154 0x0040EB28 0x00400000 0x00000000
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The correct number for QCA9377 chip is 33 VDEVs.
This impacts also QCA6174 chip and it's max VDEV number.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_tx_free_cont_txbuf' and 'ath10k_htt_tx_free_cont_frag_desc'
have NULL pointer checks to avoid crash if they are called twice
but this is as of now not sufficient as these pointers are not assigned
to NULL once the contiguous DMA memory allocation is freed, fix this.
Though this may not be hit with the explicity check of state variable
'tx_mem_allocated' check, good to have this addressed as well.
Below BUG_ON is hit when the above scenario is simulated
with kernel debugging enabled
page:f6d09a00 count:0 mapcount:-127 mapping: (null)
index:0x0
flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page)
== 0)
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:445!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP is at put_page_testzero.part.88+0xd/0xf
Call Trace:
[<c118a2cc>] __free_pages+0x3c/0x40
[<c118a30e>] free_pages+0x3e/0x50
[<c10222b4>] dma_generic_free_coherent+0x24/0x30
[<f8c1d9a8>] ath10k_htt_tx_free_cont_txbuf+0xf8/0x140
[<f8c1e2a9>] ath10k_htt_tx_destroy+0x29/0xa0
[<f8c143e0>] ath10k_core_destroy+0x60/0x80 [ath10k_core]
[<f8acd7e9>] ath10k_pci_remove+0x79/0xa0 [ath10k_pci]
[<c13ed7a8>] pci_device_remove+0x38/0xb0
[<c14d3492>] __device_release_driver+0x72/0x100
[<c14d36b7>] driver_detach+0x97/0xa0
[<c14d29c0>] bus_remove_driver+0x40/0x80
[<c14d427a>] driver_unregister+0x2a/0x60
[<c13ec768>] pci_unregister_driver+0x18/0x70
[<f8aced4f>] ath10k_pci_exit+0xd/0x2be [ath10k_pci]
[<c1101e78>] SyS_delete_module+0x158/0x210
[<c11b34f1>] ? __might_fault+0x41/0xa0
[<c11b353b>] ? __might_fault+0x8b/0xa0
[<c1001a4b>] do_fast_syscall_32+0x9b/0x1c0
[<c178da34>] sysenter_past_esp+0x45/0x74
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to receive other BSS entries in mesh mode, Monitor vdev
is created whenever filter flag is set with OTHER_BSS. Recently
it is root caused that setting promisc filter for Mesh interface
is causing performance and stability issues. To fix this issue,
firmware will configure appropriate rxfilters by default for mesh
vdev during vdev creation. This change fixes monitor vdev creation
based on firmware IE
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
