Reference platform
==================

SERV comes with a small FPGA-focused reference platform called Servant, which is capable of running Zephyr RTOS, the regression test suite and other software. The platform consists of SERV, a timer, memory and a 1-bit GPIO output pin.

.. image:: servant.png

Available targets
-----------------

The servant SoC has been ported to an increasing number of different FPGA boards and is easy to modify for new targets. To see all currently supported targets run:

    fusesoc core show servant

By default, these targets have the program memory preloaded with a small Zephyr hello world example that writes its output on a UART pin. Don't forget to install the appropriate toolchain (e.g. icestorm, Vivado, Quartus...) and add to your PATH

Some targets also depend on functionality in the FuseSoC base library (fusesoc-cores). Running `fusesoc library list` should tell you if fusesoc-cores is already available. If not, add it to your workspace with

    fusesoc library add fusesoc-cores https://github.com/fusesoc/fusesoc-cores

Now we're ready to build. Note, for all the cases below, it's possible to run with `--memfile=$SERV/sw/blinky.hex`
(or any other suitable program) as the last argument to preload the LED blink example
instead of hello world.

Alhambra II
^^^^^^^^^^^

Pin 61 is used for UART output with 115200 baud rate. This pin is connected to a FT2232H chip in board, that manages the communications between the FPGA and the computer.

    fusesoc run --target=alhambra servant
    iceprog -d i:0x0403:0x6010:0 build/servant_1.0.1/alhambra-icestorm/servant_1.0.1.bin

Alinx ax309 (Spartan6 LX9)
^^^^^^^^^^^^^^^^^^^^^^^^^^

Pin D12 (the on-board RS232 TX pin) is used for UART output with 115200 baud rate and wired to Pin P4 (LED0).

    fusesoc run --target=ax309 servant

Arty A7 35T
^^^^^^^^^^^

Pin D10 (uart_rxd_out) is used for UART output with 57600 baud rate (to use
blinky.hex change D10 to H5 (led[4]) in data/arty_a7_35t.xdc).

    fusesoc run --target=arty_a7_35t servant

Chameleon96 (Arrow 96 CV SoC Board)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

FPGA Pin W14 (1V8, pin 5 low speed connector) is used for UART Tx output with 115200 baud rate. No reset key. Yellow Wifi led is q output.

    fusesoc run --target=chameleon96 servant

DE0 Nano
^^^^^^^^

FPGA Pin D11 (Connector JP1, pin 38) is used for UART output with 57600 baud rate. DE0 Nano needs an external 3.3V UART to connect to this pin

    fusesoc run --target=de0_nano servant

DE10 Nano
^^^^^^^^^

FPGA Pin Y15 (Connector JP7, pin 1) is used for UART output with 57600 baud rate. DE10 Nano needs an external 3.3V UART to connect to this pin

    fusesoc run --target=de10_nano servant

DECA development kit
^^^^^^^^^^^^^^^^^^^^

FPGA Pin W18 (Pin 3 P8 connector) is used for UART output with 57600 baud rate. Key 0 is reset and Led 0 q output.

    fusesoc run --target=deca servant

EBAZ4205 'Development' Board
^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Pin B20 is used for UART output with 57600 baud rate. To use `blinky.hex`
change B20 to W14 (red led) in `data/ebaz4205.xdc` file).

    fusesoc run --target=ebaz4205 servant

    fusesoc run --target=ebaz4205 servant --memfile=$SERV/sw/blinky.hex

Reference: https://github.com/fusesoc/blinky#ebaz4205-development-board

Icebreaker
^^^^^^^^^^

Pin 9 is used for UART output with 57600 baud rate.

    fusesoc run --target=icebreaker servant

iCEstick
^^^^^^^^

Pin 95 is used as the GPIO output which is connected to the board's green LED. Due to this board's limited Embedded BRAM, programs with a maximum of 7168 bytes can be loaded. The default program for this board is blinky.hex.

    fusesoc run --target=icestick servant
    iceprog build/servant_1.2.1/icestick-icestorm/servant_1.2.1.bin

iCESugar
^^^^^^^^

Pin 6 is used for UART output with 115200 baud rate. Thanks to the onboard
debugger, you can just connect the USB Type-C connector to the PC, and a
serial console will show up.

    fusesoc run --target=icesugar servant

ICE-V Wireless
^^^^^^^^^^^^^^

Pin 9 is used for UART output with 57600 baud rate.

    fusesoc run --target=icev_wireless servant

    iceprog build/servant_1.2.1/icestick-icestorm/servant_1.2.1.bin

Nandland Go Board
^^^^^^^^^^^^^^^^^

Pin 56 is used as the GPIO output which is connected to the board's LED1. Due to this board's limited Embedded BRAM, programs with a maximum of 7168 bytes can be loaded. The default program for this board is blinky.hex.

    fusesoc run --target=go_board servant
    iceprog build/servant_1.2.1/go_board-icestorm/servant_1.2.1.bin

Nexys 2
^^^^^^^

Pmod pin JA1 is conntected to UART tx with 57600 baud rate. A USB to TTL connector is used to display to hello world message on the serial monitor.
(To use blinky.hex change L15 to J14 (led[0]) in data/nexys_2.ucf).

    fusesoc run --target=nexys_2_500 servant --uart_baudrate=57600 --firmware=$SERV/sw/zephyr_hello.hex


OrangeCrab R0.2
^^^^^^^^^^^^^^^

Pin D1 is used for UART output with 115200 baud rate.

    fusesoc run --target=orangecrab_r0.2 servant
    dfu-util -d 1209:5af0 -D build/servant_1.2.1/orangecrab_r0.2-trellis/servant_1.2.1.bit

Saanlima Pipistrello (Spartan6 LX45)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Pin A10 (usb_data<1>) is used for UART output with 57600 baud rate (to use
blinky.hex change A10 to V16 (led[0]) in data/pipistrello.ucf).

    fusesoc run --target=pipistrello servant

SoCKit development kit
^^^^^^^^^^^^^^^^^^^^^^

FPGA Pin F14 (HSTC GPIO addon connector J2, pin 2) is used for UART output with 57600 baud rate.

    fusesoc run --target=sockit servant

TinyFPGA BX
^^^^^^^^^^^

Pin A6 is used for UART output with 115200 baud rate.

    fusesoc run --target=tinyfpga_bx servant
    tinyprog --program build/servant_1.0.1/tinyfpga_bx-icestorm/servant_1.0.1.bin