Some qcom platforms make some GPIOs or pins unavailable for use by
non-secure operating systems, and thus reading or writing the registers
for those pins will cause access control issues. Add support for a DT
property to describe the set of GPIOs that are available for use so that
higher level OSes are able to know what pins to avoid reading/writing.
Non-DT platforms can add support by directly updating the
chip->valid_mask.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We don't need to clear out these bits when we set them immediately
after. Use kmalloc_array() to skip clearing the bits.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We're going to use similar code to allocate and set all the bits in a
mask for valid gpios to use. Extract the code from the irqchip version
so it can be reused.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we failed to create the top debugfs directory, we must not try to
create the child nodes. We currently only check if gpio_mockup_dbg_dir
is not NULL, but it can also contain an errno if debugfs is disabled
in build options. Use IS_ERR_OR_NULL() instead.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Pyra-Handheld originally used the tca6424 but recently we have
replaced it by the pin and package compatible pcal6524. So let's
add this to the bindings and the driver.
And while we are at it, the pcal9555a does not have a compatible entry
either but is already supported by the device id table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable an optional bus clock provided by DT.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new challenge is to remove VLAs from the kernel
(see https://lkml.org/lkml/2018/3/7/621)
This patch replaces a VLA with an appropriate call to kmalloc_array.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new challenge is to remove VLAs from the kernel
(see https://lkml.org/lkml/2018/3/7/621)
This patch replaces several a VLA with an appropriate call to
kmalloc_array.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-and-tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 device provides 48 lines of digital I/O accessed
via six 8-bit ports. Since eight input lines are acquired on a single
port input read, the WS16C48 GPIO driver may improve multiple input
reads by utilizing a get_multiple callback. This patch implements the
ws16c48_gpio_get_multiple function which serves as the respective
get_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Diamond Systems GPIO-MM series of devices contain two 82C55A
devices, which each feature three 8-bit ports of I/O. Since eight input
lines are acquired on a single port input read, the GPIO-MM GPIO driver
may improve multiple input reads by utilizing a get_multiple callback.
This patch implements the gpiomm_gpio_get_multiple function which serves
as the respective get_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES I/O 104-IDI-48 series of devices provides 48
optically-isolated inputs accessed via six 8-bit ports. Since eight
input lines are acquired on a single port input read, the 104-IDI-48
GPIO driver may improve multiple input reads by utilizing a get_multiple
callback. This patch implements the idi_48_gpio_get_multiple function
which serves as the respective get_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES I/O 104-DIO-48E series of devices contain two Programmable
Peripheral Interface (PPI) chips of type 82C55, which each feature three
8-bit ports of I/O. Since eight input lines are acquired on a single
port input read, the 104-DIO-48E GPIO driver may improve multiple input
reads by utilizing a get_multiple callback. This patch implements the
dio48e_gpio_get_multiple function which serves as the respective
get_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES I/O PCIe-IDIO-24 series of devices provides 24
optically-isolated digital I/O accessed via six 8-bit ports. Since eight
input lines are acquired on a single port input read -- and similarly
eight output lines are set on a single port output write -- the
PCIe-IDIO-24 GPIO driver may improve multiple I/O reads/writes by
utilizing a get_multiple/set_multiple callbacks. This patch implements
the idio_24_gpio_get_multiple function which serves as the respective
get_multiple callback, and implements the idio_24_gpio_set_multiple
function which serves as the respective set_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES I/O PCI-IDIO-16 series of devices provides 16
optically-isolated digital inputs accessed via two 8-bit ports. Since
eight input lines are acquired on a single port input read, the
PCI-IDIO-16 GPIO driver may improve multiple input reads by utilizing a
get_multiple callback. This patch implements the
idio_16_gpio_get_multiple function which serves as the respective
get_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES I/O 104-IDIO-16 series of devices provides 16
optically-isolated digital inputs accessed via two 8-bit ports. Since
eight input lines are acquired on a single port input read, the
104-IDIO-16 GPIO driver may improve multiple input reads by utilizing a
get_multiple callback. This patch implements the
idio_16_gpio_get_multiple function which serves as the respective
get_multiple callback.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using BIT() makes (1 << foo) constructions easier to read, and
also account for common mistakes where bit 31 is not working
because of numbers being interpreted as negative unless
specified as unsigned.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is a pure GPIO driver and should only include
<linux/gpio/driver.h>. Refrain from using GPIOF_* flags in
the driver, just use 1/0 to return direction.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is a pure GPIO driver and should only include
<linux/gpio/driver.h>. Drop the include of <linux/gpio.h>
from the platform data header as well, it serves no purpose.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Emma Mobile (EM) GPIO driver uses the too generic include
<linux/gpio.h>. It is a driver so it should just use
<linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver has no business including <linux/gpio.h>, it is a
driver so include <linux/gpio/driver.h>.
GPIOF_DIR_IN/GPIOF_DIR_OUT are for consumers and should not be
used in drivers to use just 1/0 instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bamvor changed his mail so let's updat his mail address
everywhere.
Cc: Bamvor Jian Zhang <bamv2005@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit ab82fa7da4 ("gpio: rcar: Prevent module clock disable
when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 7ed915059c (gpio: raspberrypi-ext: fix firmware dependency)
fixed the Kconfig dependency to ensure that gpio-raspberrypi-exp is not
built-in when the firmware is a module. But the Kconfig syntax for doing
so is cryptic. Add a comment to make it a little easier.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Spreadtrum SC9860 platform GPIO controller contains 16 groups and
each group contains 16 GPIOs. Each GPIO can set input/output and has
the interrupt capability.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the firmware driver is a loadable module, the gpio driver cannot be
built-in:
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_set':
gpio-raspberrypi-exp.c:(.text+0xb4): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_get':
gpio-raspberrypi-exp.c:(.text+0x1ec): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_get_direction':
gpio-raspberrypi-exp.c:(.text+0x360): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_get_polarity':
gpio-raspberrypi-exp.c:(.text+0x4d4): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_dir_out':
gpio-raspberrypi-exp.c:(.text+0x670): undefined reference to `rpi_firmware_property'
drivers/gpio/gpio-raspberrypi-exp.o:gpio-raspberrypi-exp.c:(.text+0x7fc): more undefined references to `rpi_firmware_property' follow
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_dir_in':
drivers/gpio/gpio-raspberrypi-exp.o: In function `rpi_exp_gpio_probe':
gpio-raspberrypi-exp.c:(.text+0x93c): undefined reference to `rpi_firmware_get'
We already have a Kconfig dependency for it, but when compile-testing, it
is disregarded.
This changes the dependency so that compile-testing is only done when the
firmware driver is completely disabled.
Fixes: a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
"failed" maybe makes observer confuse when a consumer can not
lookup, so change to a friendly information.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 GPIO drivers. They are of no value without the
architecture and SoC platform code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_named_gpiod_flags() used directly in of_find_gpio() or indirectly
through of_find_spi_gpio() or of_find_regulator_gpio() can return
-EPROBE_DEFER. This gets overwritten by the subsequent of_find_*_gpio()
calls.
This patch fixes this by trying of_find_spi_gpio() or
of_find_regulator_gpio() only if deferred probing was not requested by
the previous of_get_named_gpiod_flags() call.
Fixes: 6a537d4846 ("gpio: of: Support regulator nonstandard GPIO properties")
Fixes: c858233902 ("gpio: of: Support SPI nonstandard GPIO properties")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[Augmented to fit with Maxime's patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commits c858233902 ("gpio: of: Support SPI nonstandard GPIO properties")
and 6a537d4846 ("gpio: of: Support regulator nonstandard GPIO
properties") have introduced a regression in the way error codes from
of_get_named_gpiod_flags are handled.
Previously, those errors codes were returned immediately, but the two
commits mentioned above are now overwriting the error pointer, meaning that
whatever value has been returned will be dropped in favor of whatever the
two new functions will return.
This might not be a big deal except for EPROBE_DEFER, on which GPIOlib
customers will depend on, and that will now be returned as an hard error
which means that they will not probe anymore, instead of gently deferring
their probe.
Since EPROBE_DEFER basically means that we have found a valid property but
there was no GPIO controller registered to handle it, fix this issues by
returning it as soon as we encounter it.
Fixes: c858233902 ("gpio: of: Support SPI nonstandard GPIO properties")
Fixes: 6a537d4846 ("gpio: of: Support regulator nonstandard GPIO properties")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[Fold in fix to the fix]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 92a8046c9d.
Now that the patch series changing ISA_BUS_API dependency to selection
was merged this reversion will do the same for gpio-winbond driver to
make it consistent with other ISA bus gpio drivers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds an implementation that saves and restores the state of
GPIO configuration on suspend and resume.
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Modify structure of the bank info to simplify a saving registers]
[Remove DEV_PM_OPS macro]
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were going out through the (legacy) gpio API to read the value
of a line to set up polarity inversion. This is abusive. Do something
less abusive by looking up the actual struct gpio_chip *
instance and calling .get() directly on it.
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This terminology is more precise. Also cut the stride calculation
in the preprocessor, it confuses more than it helps when reading
the driver.
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are forward-declaring enum gpiod_flags, but this is not referenced
by pointer, it is a real struct member, so we need to actually include
it to compile anything including the local gpiolib.h header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
