By default NIXLF is set in UCAST mode. This patch adds a new
mailbox message which when sent by a RVU PF changes this default
mode. When promiscuous mode is needed, the reserved promisc entry
for each of RVU PF is setup to match against ingress channel number
only, so that all pkts on that channel are accepted and forwarded
to the mode change requesting PF_FUNC's NIXLF.
PROMISC and ALLMULTI modes are supported only for PFs, for VFs only
UCAST mode is supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new mailbox message for a PF/VF to set/update
it's NIXLF's MAC address. Also updates unicast NPC
MCAM entry with this address as matching DMAC.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to change
NIX Rx flowkey algorithm index in NPC RX RSS_ACTION.
eg: a ethtool command changing RSS algorithm for a netdev
interface would trigger this change in NPC.
If PF/VF doesn't specify any MCAM entry index then default
UCAST entry of the NIXLF attached to PF/VF will be updated
with RSS_ACTION and flowkey index.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon NIXLF_ALLOC install a unicast forwarding rule in NPC MCAM
like below
- Match pkt DMAC with NIXLF attached PF/VF's MAC address.
- Ingress channel
- Action is UCAST
- Forward to PF_FUNC of this NIXLF
And broadcast pkt forwarding rule as
- Match L2B bit in MCAM search key
- Ingress channel
- Action is UCAST, for now, later it will be changed to MCAST.
Only PFs can install this rule
Upon NIXLF_FREE disable all MCAM entries in use by that NIXLF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LMAC channel info like Rx/Tx channel base and count to
NIXLF_ALLOC mailbox message response. This info is used by
NIXLF attached RVU PF/VF to configure SQ's default channel,
TL3_TL2_LINKX_CFG and to install MCAM rules in NPC based
on matching ingress channel number.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some minimal configuration for NPC MCAM and
LDATA extraction which is sufficient enough to install
ucast/bcast/promiscuous forwarding rules. Below is the
config done
- LDATA extraction config to extract DMAC from pkt
to offset 64bit in MCAM search key.
- Set MCAM lookup keysize to 224bits
- Set MCAM TX miss action to UCAST_DEFAULT
- Set MCAM RX miss action to DROP
Also inorder to have guaranteed space in MCAM to install
ucast forwarding rule for each of RVU PF/VF, reserved
one MCAM entry for each of NIXLF for ucast rule. And two
entries for each of RVU PF. One for bcast pkt replication
and other for promiscuous mode which allows all pkts
received on a HW CGX/LBK channel.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for PF/VF drivers to configure NIX to
capture and/or strip VLAN tag from ingress packets.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate memory for mcast/bcast/mirror replication entry
contexts, replication buffers (used by HW) and config HW
with corresponding memory bases. Added support for installing
MCEs via NIX AQ mbox.
For now support is restricted to broadcast pkt replication,
hence MCE table size and number of replication buffers
allocated are less. Each CGX LMAC mapped RVU PF is assigned
a MCE table of size 'num VFs of that PF + PF'.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each CGX LMAC that is mapped to a RVU PF, allocate
a pkind and config the same in CGX. For a received packet
at CGX LMAC interface this pkind is used by NPC block
to start parsing of packet.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.
Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
channel mapping.
- Added all CSR offsets of NPC HW block.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new mailbox message to reset
a NIXLF's receive and transmit HW stats.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a PF/VF driver to configure
NIX transmit scheduler queues via mbox. Since PF/VF doesn't
know the absolute HW index of the NIXLF attached to it, AF
traps the register config and overwrites with the correct
NIXLF index.
HW supports shaping, colouring and policing of packets with
these multilevel traffic scheduler queues. Instead of
introducing different mbox message formats for different
configurations and making both AF & PF/VF driver implementation
cumbersome, access to the scheduler queue's CSRs is provided
via mbox. AF checks whether the sender PF/VF has the
corresponding queue allocated or not and dumps the config
to HW. With a single mbox msg 20 registers can be configured.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a PF/VF to allocate or free NIX transmit
scheduler queues via mbox. For setting up pkt transmission
priorities between queues, the scheduler queues have to be
contiguous w.r.t their HW indices. So both contiguous and
non-contiguous allocations are supported.
Upon receiving NIX_TXSCH_FREE mbox msg all scheduler queues
allocated to sending PFFUNC (PF/VF) will be freed. Selective
free is not supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to disable all RQ/SQ/CQ
contexts of a NIX LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.
A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the RQ/SQ/CQ contexts.
So a bitmap is introduced to keep track of enabled NIX RQ/SQ/CQ
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NIX AQ
via mbox. Instructions can be to init/write/read RQ/SQ/CQ/RSS
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate bitmaps and memory for PFVF mapping info for
maintaining NIX transmit scheduler queues maintenance.
PF/VF drivers will request for alloc, free e.t.c of
Tx schedulers via mailbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving NIX_LF_ALLOC mbox message allocate memory for
NIXLF's CQ, SQ, RQ, CINT, QINT and RSS HW contexts and configure
respective base iova HW. Enable caching of contexts into NIX NDC.
Return SQ buffer (SQB) size, this PF/VF MAC address etc info
e.t.c to the mbox msg sender.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NIX admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NIX LFs will submit
instructions to AQ to init/write/read RQ/SQ/CQ/RSS contexts
and in case of read, get context from result memory.
Also before configuring/using NIX block calibrate X2P bus
and check if NIX interfaces like CGX and LBK are in active
and working state.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to disable all Aura/Pool
contexts of a NPA LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.
A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the Aura/Pool contexts.
So a bitmap is introduced to keep track of enabled NPA Aura/Pool
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NPA AQ
via mbox. Instructions can be to init/write/read Aura/Pool/Qint
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving NPA_LF_ALLOC mbox message allocate memory for
NPALF's aura, pool and qint contexts and configure the same
to HW. Enable caching of contexts into NPA NDC.
Return pool related info like stack size, num pointers per
stack page e.t.c to the mbox msg sender.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NPA admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NPA LFs will submit
instructions to AQ to init/write/read Aura/Pool contexts
and in case of read, get context from result memory.
Added some common APIs for allocating memory for a queue
and get IOVA in return, these APIs will be used by
NIX AQ and for other purposes.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to enable or disable internal loopback mode in CGX.
New mbox IDs CGX_INTLBK_ENABLE/DISABLE added for this.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving notification from firmware the CGX event handler
in the AF driver gets the current link info such as status, speed,
duplex etc from CGX driver and sends it across to PFs who have
registered to receive such notifications.
To support above
- Mbox messaging support for sending msgs from AF to PF has been added.
- Added mbox msgs so that PFs can register/unregister for link events.
- Link notifications are sent to PF under two scenarioss.
1. When a asynchronous link change notification is received from
firmware with notification flag turned on for that PF.
2. Upon notification turn on request, the current link status is
send to the PF.
Also added a new mailbox msg using which RVU PF/VF can retrieve
their mapped CGX LMAC's current link info. Link info includes
status, speed, duplex and lmac type.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting MAC address filters in CGX
for PF interfaces. Also PF interfaces can be put in promiscuous
mode. Dataplane PFs access this functionality using mailbox
messages to the AF driver.
Signed-off-by: Vidhya Raman <vraman@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF driver to retrieve
it's mapped CGX LMAC Rx and Tx stats from AF via mbox.
New mailbox msg is added is added.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new mailbox msgs for RVU PF/VFs to request AF
to enable/disable their mapped CGX::LMAC Rx & Tx.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support in RVU AF driver to register for
CGX LMAC link status change events from firmware
and managing them. Processing part will be added
in followup patches.
- Introduced eventqueue for posting events from cgx lmac.
Queueing mechanism will ensure that events can be posted
and firmware can be acked immediately and hence event
reception and processing are decoupled.
- Events gets added to the queue by notification callback.
Notification callback is expected to be atomic, since it
is called from interrupt context.
- Events are dequeued and processed in a worker thread.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each of the enabled CGX LMAC is considered a physical
interface and RVU PFs are mapped to these. VFs of these
SRIOV PFs will be virtual interfaces and share CGX LMAC
along with PF.
This mapping info will be used later on for Rx/Tx pkt steering.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW interprets RVU_AF_MSIXTR_BASE address as an IOVA, hence
create a IOMMU mapping for the physcial address configured by
firmware and reconfig RVU_AF_MSIXTR_BASE with IOVA.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware configures a certain number of MSIX vectors to each of
enabled RVU PF/VF. When a block LF is attached to a PF/VF, number
of MSIX vectors needed by that LF are set aside (out of PF/VF's
total MSIX vectors) and LF's msix_offset is configured in HW.
Also added support for a RVU PF/VF to retrieve that block LF's
MSIX vector offset information from AF via mbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a RVU PF/VF to request AF via mailbox
to attach or detach NPA/NIX/SSO/SSOW/TIM/CPT block LFs.
Also supports partial detachment and modifying current
LF attached count of a certian block type.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scan all RVU blocks to find any 'LF to RVU PF/VF' mapping done by
low level firmware. If found any, mark them as used in respective
block's LF bitmap and also save mapped PF/VF's PF_FUNC info.
This is done to avoid reattaching a block LF to a different RVU PF/VF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mailbox interrupt and message
handling. Mapped mailbox region and registered a workqueue
for message handling. Enabled mailbox IRQ of RVU PFs
and registered a interrupt handler. When IRQ is triggered
work is added to the mbox workqueue for msgs to get processed.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gathers NPA/NIX/SSO/SSOW/TIM/CPT RVU blocks's
HW info like number of LFs. Important register offsets
saved for later use to avoid code duplication for each block.
A bitmap is allocated for each of the blocks which later
on will be used to allocate a LF for a RVU PF/VF.
Also added RVU NIX/NPA block registers and few registers
of other blocks.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go through all BLKADDRs and check which ones are implemented
on this silicon and do a HW reset of each implemented block.
Also added all RVU AF and PF register offsets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
resource virtualization unit (RVU) admin function (AF)
driver. Just the driver registration and probe.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
