By default NIXLF is set in UCAST mode. This patch adds a new
mailbox message which when sent by a RVU PF changes this default
mode. When promiscuous mode is needed, the reserved promisc entry
for each of RVU PF is setup to match against ingress channel number
only, so that all pkts on that channel are accepted and forwarded
to the mode change requesting PF_FUNC's NIXLF.
PROMISC and ALLMULTI modes are supported only for PFs, for VFs only
UCAST mode is supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to change
NIX Rx flowkey algorithm index in NPC RX RSS_ACTION.
eg: a ethtool command changing RSS algorithm for a netdev
interface would trigger this change in NPC.
If PF/VF doesn't specify any MCAM entry index then default
UCAST entry of the NIXLF attached to PF/VF will be updated
with RSS_ACTION and flowkey index.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon NIXLF_ALLOC install a unicast forwarding rule in NPC MCAM
like below
- Match pkt DMAC with NIXLF attached PF/VF's MAC address.
- Ingress channel
- Action is UCAST
- Forward to PF_FUNC of this NIXLF
And broadcast pkt forwarding rule as
- Match L2B bit in MCAM search key
- Ingress channel
- Action is UCAST, for now, later it will be changed to MCAST.
Only PFs can install this rule
Upon NIXLF_FREE disable all MCAM entries in use by that NIXLF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some minimal configuration for NPC MCAM and
LDATA extraction which is sufficient enough to install
ucast/bcast/promiscuous forwarding rules. Below is the
config done
- LDATA extraction config to extract DMAC from pkt
to offset 64bit in MCAM search key.
- Set MCAM lookup keysize to 224bits
- Set MCAM TX miss action to UCAST_DEFAULT
- Set MCAM RX miss action to DROP
Also inorder to have guaranteed space in MCAM to install
ucast forwarding rule for each of RVU PF/VF, reserved
one MCAM entry for each of NIXLF for ucast rule. And two
entries for each of RVU PF. One for bcast pkt replication
and other for promiscuous mode which allows all pkts
received on a HW CGX/LBK channel.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Config NPC layer info from KPU profile into protocol
checker to identify outer L2/IPv4/TCP/UDP headers in a
packet. And enable IPv4 checksum validation.
L3/L4 and L4 CSUM validation will be enabled by PF/VF
drivers by configuring NIX_AF_LF(0..127)_RX_CFG via mbox
i.e 'nix_lf_alloc_req->rx_cfg'
Also enable setting of NPC_RESULT_S[L2B] when an outer
L2 broadcast address is detected. This will help in
installing NPC MCAM rules for broadcast packets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each CGX LMAC that is mapped to a RVU PF, allocate
a pkind and config the same in CGX. For a received packet
at CGX LMAC interface this pkind is used by NPC block
to start parsing of packet.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.
Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
channel mapping.
- Added all CSR offsets of NPC HW block.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
