Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds the support of TDLS feature for 10.4 firmware
versions.
A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Though there is room to accommodate 512 services in wmi service
ready event, target uses only first 4-bits of each 32-bit word for
advertising wmi services thereby limiting max wmi services to 64.
TDLS implementation for 10.4 firmwares introduces new wmi services by
making use of remaining unused bits of each 32-bit word, therefore the
wmi service mapping in host needs to be extended.
This patch adds the logic to extend the wmi SVCMAP to accommodate new
wmi services.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As suggested by Arnd Bergmann, replace
"while (time_before_...) {}"
with
"do {} while (time_before_...)"
This fixes the following warnings detected by gcc 4.1.2:
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_mbox_rxmsg_pending_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:676: warning: ‘ret’ may be used uninitialized in this function
...
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_irq_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:1331: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA9377 have support for USB so add initial USB bus
support to ath10k. With this patch we have the low level HIF and
HTC protocol working and it's possible to boot the firmware,
but it's still not possible to connect or anything like.
More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k USB support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the a-mpdu reference number in ath10k to make it accessible in the
receivers radiotap header. Implemented as in ath9k. The reference number is
needed for troubleshooting and research at the receivers site (e.g. to identify
mpdu's that were aggregated in an a-mpdu)
Signed-off-by: Matthias Frei <mf@frei.media>
[kvalo@qca.qualcomm.com: fix checkpatch warning, commit log cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All wmi_services are not printing when we give below command.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services
This patch increases the buffer_len to 8192 to print all the wmi_services.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove bus specific dependencies from CE layer
to have common CE layer across multiple targets.
This is required for adding support for WCN3990
chipset support as WCN3990 chipset uses SNOC
bus interface with Copy Engine endpoint.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 59ae1d127a ("networking: introduce and use skb_put_data()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:3308: code indent should use tabs where possible
Fix that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following spelling mistakes in messages:
syncronise -> synchronize
unusally -> unusually
addrress -> address
inverval -> interval
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.
The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report per chain RSSI to mac80211.
Signed-off-by: Norik Dzhandzhapanyan <norikd@gmail.com>
[kvalo@qca.qualcomm.com: fix conflicts and style]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define structures for the copy engine ctrl/misc registers,
that includes CE CMD halt, watermark source, watermark destination,
host IE ring, source, destination and dmax ring.
This adds support to avoid the conditional compilation,
code optimization and dynamic configuration of the copy engine
register map for respective hardware bus interface.
Signed-off-by: Sarada Prasanna Garnayak <c_sgarna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original idea is to limit the maximum TDLS peer link, but the logic
is always false, and never be able to restrict the number of TDLS peer
creation.
Fix the logic here and also move the checking earlier, so that it could
avoid to handle the failure case, e.g disable the tdls peer, delete the
peer and also vdev count cleanup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0, QCA9888, QCA9984 supports calibration data in
either OTP or DT/pre-cal file. Current ath10k supports
Calibration data from OTP only.
If caldata is loaded from DT/pre-cal file, fetching board id
and applying calibration parameters like tx power gets failed.
error log:
[ 15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
[ 15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)
This patch adds calibration data support from DT/pre-cal
file. Below parameters are used to get board id and
applying calibration parameters from cal data.
EEPROM[OTP] FLASH[DT/pre-cal file]
Cal param 0x700 0x10000
Board id 0x10 0x8000
Tested on QCA9888 with pre-cal file.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k firmware checks nbytes == 0 as part of determining if DMA
has completed successfully. To help make this work more often,
have the driver initialize nbytes to zero when freeing the descriptor
slot.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lets one have a clue that maybe timeouts are happening
when we just aren't waiting long enough.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When testing a 9888 chipset NIC, I notice it often takes
almost 2 seconds, and then many times OTP fails, probably due
to the two-second timeout.
[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0
So, increase the BMI timeout to 3 seconds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit b057886524 ("ath10k: do not use coherent memory for
allocated device memory chunks") in 2015 which converted this allocation from
dma_map_coherent() to kzalloc() / dma_map_single().
The current problem manifests when using later model NICs with larger
(>700KiB) scratch spaces in memory. Although the kzalloc call
succeeds, the software IOMMU TLB code (via dma_map_single()) panics
because it can't find 700KiB of linear physmem bounce buffers for DMA.
Now, this is a bit of a silly failure mode for the dma map API,
but it's what we currently have to play with.
In these cases, doing kzalloc() works fine, but the dma_map_single()
call fails.
After chatting with Linus briefly about this, it indeed should be
using dma_alloc_coherent() for doing larger device memory allocation
that requires some kind of physical address mapping.
You're not supposed to be using kzalloc and dma_map_* calls for
large memory regions, and I'm guessing not for long-held mappings
either. Typically dma mappings should be temporary for DMA,
not long held like these.
Now, since hopefully the major annoying underlying problem has also been
addressed (ie, ath10k is no longer tears down all of these allocations
and reallocates them every time the vdevs are brought down) fragmentation
should stop being such a touchy issue. If it is though, using
dma_alloc_coherent() use gets us access to the CMB APIs too relatively
easily and ideally we would be allocating memory early in boot for
exactly these reasons.
Signed-off-by: Adrian Chadd <adrian@FreeBSD.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA4019 firmware 10.4-3.2.1-00050 reports only HT MCS rates between
0-9. But 802.11n MCS rates can be larger than that. For example a 2x2
device can send with up to MCS 15.
The firmware encodes the higher MCS rates using the NSS field. The actual
calculation is not documented by QCA but it seems like the NSS field can be
mapped for HT rates to following MCS offsets:
* NSS 1: 0
* NSS 2: 8
* NSS 3: 16
* NSS 4: 24
This offset therefore has to be added for HT rates before they are stored
in the rate_info struct.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The array fields in struct wmi_start_scan_arg that are checked here are
fixed size arrays so they can never be NULL.
Addresses-Coverity-ID: 1260031
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9xxx and QCA61x4/QCA93xx are using different wmi operation, in order
for userspace to differentiate it, appends the wmi_op_version information
alone with the get_version command.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During write to debugfs file simulate_fw_crash, fixed-size local buffer
'buf' is accessed and modified at index 'count-1', where 'count' is the
size of the write (so potentially out of bounds).
This patch fixes this problem.
Signed-off-by: Michael Mera <dev@michaelmera.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA6584 have support for SDIO so add initial SDIO bus support to
ath10k. With this patch we have the low level HTC protocol working and it's
possible to boot the firmware, but it's still not possible to connect or
anything like. More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k SDIO support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: refactoring, cleanup, commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since both SDIO based chipsets will use different
firmware from the PCIe and AHB chipsets, the fw file name
must be different depending on bus type.
The new firmware names are:
For PCIe and AHB:
firmware-<api_version>.bin (same as before)
For SDIO:
firmware-sdio-<api_version>.bin
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added support for extended ready message.
The extended ready message contains the maximum bundle
count supported by SDIO chipsets.
It is transmitted by SDIO chipset only and replaces the
"standard" ready message in this case.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Special BMI get target info function for SDIO.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Extra initializations needed by all sdio boards.
Derived from qcacld.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debug masks for SDIO HIF layer.
Address definitions for SDIO/mbox based chipsets.
Augmented struct host_interest with more members.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code refactorization:
Moved the code for ep 0 in ath10k_htc_rx_completion_handler
to ath10k_htc_control_rx_complete.
This eases the implementation of SDIO/mbox significantly since
the ep_rx_complete cb is invoked directly from the SDIO/mbox
hif layer.
Since the ath10k_htc_control_rx_complete already is present
(only containing a warning message) there is no reason for not
using it (instead of having a special case for ep 0 in
ath10k_htc_rx_completion_handler).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves the HTC ctrl service connect from
htc_wait_target to htc_init.
This is done in order to make sure the htc ctrl service
is setup properly before hif_start is called.
The reason for this is that we want the HTC ctrl service
callback to be initialized before the target sends the
HTC ready message.
The ready message will always be transmitted on endpoint 0
(which is always assigned to the HTC control service) so it
makes more sense if HTC control has been connected before the
ready message is received.
Since the service to pipe mapping is done as a part of
the service connect, the get_default_pipe call is redundant
and was removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The RX trailer parsing is now capable of parsing lookahead reports.
A lookahead contains the first 4 bytes of the next HTC message
(that will be read in the next SDIO read operation).
Lookaheads are used by the SDIO/mbox HIF layer to determine if
the next message is part of a bundle, which endpoint it belongs
to and how long it is.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Changed ath10k_htc_notify_tx_completion and
ath10k_htc_process_trailer from static to non static.
These functions are needed by SDIO/mbox.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+cipAAoJEG4XJFUm622b+04H/2u7zhIqv3R5NsmGRlwjKmvd
6us1hcYzUiBW1kBFFtcvokwgqv3Rw/EUi+NYA5UCHgo30HTVJWTqW0q+BUEI7U0X
iwuFdHbs/qjj8hXKgZwaJMVyRhXAbq+iHYaMY5OEDNTRSbxqXA4V69SHGK9vLX0l
KQLJBZX3etnwsyRWrmd4E0roGGfD5tMPpGMUDSlvTPWt0I+1QFUxRI9ohn1fRBpD
p+UHHC+SYF6NzxvfqyPwm6ndb2XOwdAKYljlf4KrBwHtSXvAH8p5EASm4PjGbavY
0mrkv0cb8QOKQNVe9q4B4AmM4iAITZ9i3sQBPJ+EBN2P+kS/lFU5L/+5z3VQjms=
=KTEG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.12. Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
For QCA6174 hw3.0, since WLAN.RM.4.4-00022-QCARMSWPZ-2, it starts to
support the board ID information from otp, with some devices released on
the market that didn't calibrated with OTP, will have 0 for board ID
information, which cause the backward compatibility issue and was fixed
in commit 'd2e202c06c ("ath10k: ignore configuring the incorrect board_id")'
So bump the fw api version to differentiate the latest firmware support.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
spectral_bin length (number of bins per fft sample) is usually
a value where (2^n = value), n is an integer. All of the QCA99X0
family of chipsets seems to report a spectral_bin length of
2^n + 'm' bytes, where m = 4, 12 based on the chipset. This 'm'
bytes seems to carry some radar related info which is currently
discarded only for 'bin_len = 68' bytes. Extend this discarding of
irrelevant 'bin_len' for QCA9984, QCA9888, IPQ4019 as well by
introducing a hardware parameter 'spectral_bin_discard'. Also
for QCA988X based family of chipsets which doesn't seem to have this
issue and also for some of the hardware which I have not tested
like QCA6174/QCA9377 the existing behaviour is retained as it is.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
