Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the capability to map non-linear xdp frames in XDP_TX and
ndo_xdp_xmit callback.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220817173628.109102-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initially merged version of the igc driver code (via commit
146740f9ab, "igc: Add support for PF") contained the following
IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors:
u32 igc_rd32(struct igc_hw *hw, u32 reg)
{
u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr);
u32 value = 0;
if (IGC_REMOVED(hw_addr))
return ~value;
value = readl(&hw_addr[reg]);
/* reads should not return all F's */
if (!(~value) && (!reg || !(~readl(hw_addr))))
hw->hw_addr = NULL;
return value;
}
And:
#define wr32(reg, val) \
do { \
u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \
if (!IGC_REMOVED(hw_addr)) \
writel((val), &hw_addr[(reg)]); \
} while (0)
E.g. igb has similar checks in its MMIO accessors, and has a similar
macro E1000_REMOVED, which is implemented as follows:
#define E1000_REMOVED(h) unlikely(!(h))
These checks serve to detect and take note of an 0xffffffff MMIO read
return from the device, which can be caused by a PCIe link flap or some
other kind of PCI bus error, and to avoid performing MMIO reads and
writes from that point onwards.
However, the IGC_REMOVED macro was not originally implemented:
#ifndef IGC_REMOVED
#define IGC_REMOVED(a) (0)
#endif /* IGC_REMOVED */
This led to the IGC_REMOVED logic to be removed entirely in a
subsequent commit (commit 3c215fb18e, "igc: remove IGC_REMOVED
function"), with the rationale that such checks matter only for
virtualization and that igc does not support virtualization -- but a
PCIe device can become detached even without virtualization being in
use, and without proper checks, a PCIe bus error affecting an igc
adapter will lead to various NULL pointer dereferences, as the first
access after the error will set hw->hw_addr to NULL, and subsequent
accesses will blindly dereference this now-NULL pointer.
This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and
implements IGC_REMOVED the way it is done for igb, by checking for the
unlikely() case of hw_addr being NULL. This change prevents the oopses
seen when a PCIe link flap occurs on an igc adapter.
Fixes: 146740f9ab ("igc: Add support for PF")
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igc_set_spd_dplx method is not used. This patch comes to tidy up
the driver code.
Reported-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Time synchronization was not properly enabled on non-MSI-X platforms.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Signed-off-by: James McLaughlin <james.mclaughlin@qsc.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igc driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
Enabling the XDP bpf_prog access to data_meta area is a very small
change. Hint passing 'true' to xdp_prepare_buff().
The SKB layers can also access data_meta area, which required more
driver changes to support. Reviewers, notice the igc driver have two
different functions that can create SKBs, depending on driver config.
Hint for testers, ethtool priv-flags legacy-rx enables
the function igc_construct_skb()
ethtool --set-priv-flags DEV legacy-rx on
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Driver already implicitly supports XDP metadata access in AF_XDP
zero-copy mode, as xsk_buff_pool's xp_alloc() naturally set xdp_buff
data_meta equal data.
This works fine for XDP and AF_XDP, but if a BPF-prog adjust via
bpf_xdp_adjust_meta() and choose to call XDP_PASS, then igc function
igc_construct_skb_zc() will construct an invalid SKB packet. The
function correctly include the xdp->data_meta area in the memcpy, but
forgot to pull header to take metasize into account.
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new device ID for the next step of the silicon and
reflect the I226_LMVP part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff36 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for Credit-based shaper(CBS) Qdisc hardware
offload mode in the driver. There are two sets of IEEE802.1Qav
(CBS) HW logic in i225 controller and this patch supports
enabling them in the top two priority TX queues.
Driver implemented as recommended by Foxville External
Architecture Specification v0.993. Idleslope and Hi-credit are
the CBS tunable parameters for i225 NIC, programmed in TQAVCC
and TQAVHC registers respectively.
In-order for IEEE802.1Qav (CBS) algorithm to work as intended
and provide BW reservation CBS should be enabled in highest
priority queue first. If we enable CBS on any of low priority
queues, the traffic in high priority queue does not allow low
priority queue to be selected for transmission and bandwidth
reservation is not guaranteed.
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Separates the procedure done during reset from applying a
configuration, knowing when the code is executing allow us to
separate the better what changes the hardware state from what
changes only the driver state.
Introduces a flag for bookkeeping the driver state of TSN
features. When Qav and frame-preemption is also implemented
this flag makes it easier to keep track on whether a TSN feature
driver state is enabled or not though controller state changes,
say, during a reset.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sets default values for each queue cycle start and cycle end.
This allows some simplification in the handling of these
configurations as most TSN features in i225 require a cycle
to be configured.
In i225, cycle start and end time is required to be programmed
for CBS to work properly.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enables PCIe PTM (Precision Time Measurement) support in the igc
driver. Notifies the PCI devices that PCIe PTM should be enabled.
PCIe PTM is similar protocol to PTP (Precision Time Protocol) running
in the PCIe fabric, it allows devices to report time measurements from
their internal clocks and the correlation with the PCIe root clock.
The i225 NIC exposes some registers that expose those time
measurements, those registers will be used, in later patches, to
implement the PTP_SYS_OFFSET_PRECISE ioctl().
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde6 ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the cycle time is set to maximum of 1s, the TX Hang timeout need to
be increase to avoid possible TX Hang.
There is no dedicated number specific in data sheet for the timeout factor.
Timeout factor was determined during the debugging to solve the "Tx Hang"
issues that happen in some cases mainly during ETF(Earliest TxTime First).
This can be test by using TSN Schedule Tx Tools udp_tai sample application.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one phy->type: copper. There is no point checking
phy->type during the igc_has_link method from the watchdog that
invoked every 2 seconds.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one PHY vendor. There is no point checking
_I_PHY_ID during the link establishment and auto-negotiation process.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit cf8331825a.
There are better Linux interfaces to export the different LED modes
and blinking reasons.
Revert this patch for now and come up with better solution later.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20210719101640.16047-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each i225 has three LEDs. Export them via the LED class framework.
Each LED is controllable via sysfs. Example:
$ cd /sys/class/leds/igc_led0
$ cat brightness # Current Mode
$ cat max_brightness # 15
$ echo 0 > brightness # Mode 0
$ echo 1 > brightness # Mode 1
The brightness field here reflects the different LED modes ranging
from 0 to 15.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently flex filters are only used for filters containing user data.
However, it makes sense to utilize them also for filters having
multiple conditions, because that's not supported by the driver at the
moment. Add it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex filter mechanism to extend the current ethtool filter
operations by intercoperating the user data. This allows to match
eight more bytes within a Ethernet frame in addition to macs, ether
types and vlan.
The matching pattern looks like this:
* dest_mac [6]
* src_mac [6]
* tpid [2]
* vlan tci [2]
* ether type [2]
* user data [8]
This can be used to match Profinet traffic classes by FrameID range.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel i225 NIC has the possibility to add flex filters which can
match up to the first 128 byte of a packet. These filters are useful
for all kind of packet matching. One particular use case is Profinet,
as the different traffic classes are distinguished by the frame id
range which cannot be matched by any other means.
Add code to configure and enable flex filters.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: c9a11c23ce ("igc: Add netdev")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> # i40e
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-12-toke@redhat.com
Add HW VLAN acceleration protocol handling. In case of HW VLAN tagging,
we need that protocol available in the ndo_start_xmit(), so that it will be
stored in a new fields in the skb.
HW offloading is set to OFF by default.
Users are allow to turn on/off Rx/Tx HW VLAN acceleration via ethtool.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 73f1071c1d ("igc: Add support for XDP_TX action")
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for transmitting packets via AF_XDP zero-copy mechanism.
The packet transmission itself is implemented by igc_xdp_xmit_zc() which
is called from igc_clean_tx_irq() when the ring has AF_XDP zero-copy
enabled. Likewise i40e and ice drivers, the transmission budget used is
the number of descriptors available on the ring.
A new tx buffer type is introduced to 'enum igc_tx_buffer_type' to
indicate the tx buffer uses memory from xsk pool so it can be properly
cleaned after transmission or when the ring is cleaned.
The I225 controller has only 4 Tx hardware queues so the main difference
between igc and other Intel drivers that support AF_XDP zero-copy is
that there is no tx ring dedicated exclusively to XDP. Instead, tx
rings are shared between the network stack and XDP, and netdev queue
lock is used to ensure mutual exclusion. This is the same approach
implemented to support XDP_TX and XDP_REDIRECT actions.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for receiving packets via AF_XDP zero-copy mechanism.
Add a new flag to 'enum igc_ring_flags_t' to indicate the ring has
AF_XDP zero-copy enabled so proper ring setup is carried out during ring
configuration in igc_configure_rx_ring().
RX buffers can now be allocated via the shared pages mechanism (default
behavior of the driver) or via xsk pool (when AF_XDP zero-copy is
enabled) so a union is added to the 'struct igc_rx_buffer' to cover both
cases.
When AF_XDP zero-copy is enabled, rx buffers are allocated from the xsk
pool using the new helper igc_alloc_rx_buffers_zc() which is the
counterpart of igc_alloc_rx_buffers().
Likewise other Intel drivers that support AF_XDP zero-copy, in igc we
have a dedicated path for cleaning up rx irqs when zero-copy is enabled.
This avoids adding too many checks within igc_clean_rx_irq(), resulting
in a more readable and efficient code since this function is called from
the hot-path of the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Up to this point, Tx buffers are associated with either a skb or a xdpf,
and the IGC_TX_FLAGS_XDP flag was enough to distinguish between these
two case. However, with upcoming patches that will add AF_XDP zero-copy
support, a third case will be introduced so this flag-based approach
won't fit well.
In preparation to land AF_XDP zero-copy support, replace the
IGC_TX_FLAGS_XDP flag by an enum which will be extended once zero-copy
support is introduced to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
unmaps Tx buffers into its own local helper so we can reuse it, avoiding
code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
updates the driver RX stats in its own local helper so it can be reused
in the zero-copy path. Likewise, encapsulate TX stats code as well.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor XDP rxq info registration code, preparing the driver for AF_XDP
zero-copy support which is added by upcoming patches.
Currently, xdp_rxq and memory model are both registered during RX
resource setup time by igc_xdp_register_rxq_info() helper. With AF_XDP,
we want to register the memory model later on while configuring the ring
because we will know which memory model type to register
(MEM_TYPE_PAGE_SHARED or MEM_TYPE_XSK_BUFF_POOL).
The helpers igc_xdp_register_rxq_info() and igc_xdp_unregister_rxq_
info() are not useful anymore so they are removed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor igc_clean_rx_ring() helper, preparing the code for AF_XDP
zero-copy support which is added by upcoming patches.
The refactor consists of encapsulating page-shared specific code into
its own helper, leaving common code that will be shared by both
page-shared and xsk pool in igc_clean_rx_ring().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
