has_irq member of struct dwapb_port_property is used only in one place,
so, make it local test instead and remove from the structure.
This local test is using memchr_inv() which is quite efficient in comparison
to the original loop and possible little overhead can be neglected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that the non-DT IM-PD1 support code has been removed, drop the clock
related code from clk-impd1.c.
Link: https://lore.kernel.org/r/20200428204945.21067-1-robh@kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On Asus 2-in-1s with a detachable keyboard the Asus WMI interface
reports if the tablet is attached to the keyboard or not.
Report if the 2-in-1 is in tablet or clamshell mode to userspace
by reporting SW_TABLET_MODE events to userspace.
This has been tested on a T100TA, T100CHI, T100HA and T200TA.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix a resource allocation issue in cros_ec_sensorhub.c.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXrIE1wAKCRBzbaomhzOw
wrteAP4hRbJPMRDIXm5zc5TgqCk7YwgnJDWSjZTRNj0DyMlg9AEA1g9/DHPH20J5
jmd8OZR8c64BQBIM1dNc63F6NkikVg0=
=cd4R
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-fixes-for-v5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform fix from Benson Leung:
"Fix a resource allocation issue in cros_ec_sensorhub.c"
* tag 'tag-chrome-platform-fixes-for-v5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_sensorhub: Allocate sensorhub resource before claiming sensors
Move driver-private definitions out of the i2c-pxa.h platform data
header file into the driver itself. Nothing outside of the driver
makes use of these constants.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Allocate callbacks array before enumerating the sensors: The probe routine
for these sensors (for instance cros_ec_sensors_probe) can be called
within the sensorhub probe routine (cros_ec_sensors_probe())
Fixes: 145d59baff ("platform/chrome: cros_ec_sensorhub: Add FIFO support")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
There's quite a few changes this time around. Most of these are fixes
and cleanups, but there's also new chip support for some drivers and a
bit of rework.
-----BEGIN PGP SIGNATURE-----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=Ugxz
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There's quite a few changes this time around.
Most of these are fixes and cleanups, but there's also new chip
support for some drivers and a bit of rework"
* tag 'pwm/for-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (33 commits)
pwm: pca9685: Fix PWM/GPIO inter-operation
pwm: Make pwm_apply_state_debug() static
pwm: meson: Remove redundant assignment to variable fin_freq
pwm: jz4740: Allow selection of PWM channels 0 and 1
pwm: jz4740: Obtain regmap from parent node
pwm: jz4740: Improve algorithm of clock calculation
pwm: jz4740: Use clocks from TCU driver
pwm: sun4i: Remove redundant needs_delay
pwm: omap-dmtimer: Implement .apply callback
pwm: omap-dmtimer: Do not disable PWM before changing period/duty_cycle
pwm: omap-dmtimer: Fix PWM enabling sequence
pwm: omap-dmtimer: Update description for PWM OMAP DM timer
pwm: omap-dmtimer: Drop unused header file
pwm: renesas-tpu: Drop confusing registered message
pwm: renesas-tpu: Fix late Runtime PM enablement
pwm: rcar: Fix late Runtime PM enablement
dt-bindings: pwm: renesas-tpu: Document more R-Car Gen2 support
pwm: meson: Fix confusing indentation
pwm: pca9685: Use gpio core provided macro GPIO_LINE_DIRECTION_OUT
pwm: pca9685: Replace CONFIG_PM with __maybe_unused
...
* cros-usbpd-notify and cros_ec_typec
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
* CrOS EC
- Introduce a new cros_ec_cmd_xfer_status helper
* Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
* Wilco EC
- Fix a build warning.
- Platform data shouldn't include kernel.h
* Misc
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in cros_ec_chardev
and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXo1lfQAKCRBzbaomhzOw
wo6TAQCKHOcrqq5Y9HYXs1QBx8e/0vVwe5Jh76Qi6hUVqXu56QEA65lBZ2ni8Udp
f6jQDFkaeYaF2tkghvuNoAkFRI6/rAk=
=j4Tt
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
cros-usbpd-notify and cros_ec_typec:
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
CrOS EC:
- Introduce a new cros_ec_cmd_xfer_status helper
Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
Wilco EC:
- Fix a build warning.
- Platform data shouldn't include kernel.h
Misc:
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in
cros_ec_chardev and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
* tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (34 commits)
platform/chrome: cros_ec_spi: Wait for USECS, not NSECS
iio: cros_ec: Use Hertz as unit for sampling frequency
iio: cros_ec: Report hwfifo_watermark_max
iio: cros_ec: Expose hwfifo_timeout
iio: cros_ec: Remove pm function
iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO
iio: expose iio_device_set_clock
iio: cros_ec: Move function description to .c file
platform/chrome: cros_ec_sensorhub: Add median filter
platform/chrome: cros_ec_sensorhub: Add code to spread timestmap
platform/chrome: cros_ec_sensorhub: Add FIFO support
platform/chrome: cros_ec_sensorhub: Add the number of sensors in sensorhub
platform/chrome: chromeos_laptop: make I2C API conversion complete
platform/chrome: wilco_ec: event: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_chardev: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_typec: Update port info from EC
platform/chrome: Add Type C connector class driver
platform/chrome: cros_usbpd_notify: Pull PD_HOST_EVENT status
platform/chrome: cros_usbpd_notify: Amend ACPI driver to plat
platform/chrome: cros_usbpd_notify: Add driver data struct
...
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCXoww9AAKCRAw5/Bqldv6
8jR+AKCVa9QsVEeMTOXHDgUaub/zC2C+VQCfQoVhFysdTH3HQ0wsqX0ck7UIGhk=
=+xca
-----END PGP SIGNATURE-----
Merge tag 'leds-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"One new driver, some driver changes, and some late minute cleanups --
but those are just whitespace so should be okay.
There are some major changes being prepared (multicolor, triggers) so
the next release likely will be more interesting"
* tag 'leds-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: core: Fix warning message when init_data
leds: make functions easier to understand
leds: sort Makefile entries
leds: old enums are not really applicable to new code
leds: ip30: label power LED as such
leds: lm3532: make bitfield 'enabled' unsigned
leds: leds-pwm: Replace zero-length array with flexible-array member
leds: leds-is31fl32xx: Replace zero-length array with flexible-array member
leds: pwm: remove useless pwm_period_ns
leds: pwm: remove header
leds: pwm: convert to atomic PWM API
leds: pwm: simplify if condition
leds: add SGI IP30 led support
leds: lm3697: fix spelling mistake "To" -> "Too"
leds: leds-bd2802: remove set but not used variable 'pdata'
leds: ns2: Convert to GPIO descriptors
leds: ns2: Absorb platform data
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including
cpuidle, pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=UTk1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
This introduces a range of improvements to the OMAP remoeteproc driver;
among other things adding devicetree, suspend/resume and watchdog
support, and adds support the remoteprocs in the DRA7xx SoC.
It introduces support for 64-bit firmware, extends the ELF loader to
support this and fixes for a number of race conditions in the recovery
handling.
It introduces a generic mechanism to allow remoteproc drivers to sync
state with remote processors during a panic, and uses this to prepare
Qualcomm remote processors for post mortem analysis.
Finally it introduces fixes to cleanly recover from crashes in the modem
firmware on production Qualcomm devices.
-----BEGIN PGP SIGNATURE-----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=5Q77
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- a range of improvements to the OMAP remoeteproc driver; among other
things adding devicetree, suspend/resume and watchdog support, and
adds support the remoteprocs in the DRA7xx SoC
- support for 64-bit firmware, extends the ELF loader to support this
and fixes for a number of race conditions in the recovery handling
- a generic mechanism to allow remoteproc drivers to sync state with
remote processors during a panic, and uses this to prepare Qualcomm
remote processors for post mortem analysis
- fixes to cleanly recover from crashes in the modem firmware on
production Qualcomm devices
* tag 'rproc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (37 commits)
remoteproc/omap: Switch to SPDX license identifiers
remoteproc/omap: Add watchdog functionality for remote processors
remoteproc/omap: Report device exceptions and trigger recovery
remoteproc/omap: Add support for runtime auto-suspend/resume
remoteproc/omap: Add support for system suspend/resume
remoteproc/omap: Request a timer(s) for remoteproc usage
remoteproc/omap: Check for undefined mailbox messages
remoteproc/omap: Remove the platform_data header
remoteproc/omap: Add support for DRA7xx remote processors
remoteproc/omap: Initialize and assign reserved memory node
remoteproc/omap: Add the rproc ops .da_to_va() implementation
remoteproc/omap: Add support to parse internal memories from DT
remoteproc/omap: Add a sanity check for DSP boot address alignment
remoteproc/omap: Add device tree support
dt-bindings: remoteproc: Add OMAP remoteproc bindings
remoteproc: qcom: Introduce panic handler for PAS and ADSP
remoteproc: qcom: q6v5: Add common panic handler
remoteproc: Introduce "panic" callback in ops
remoteproc: Traverse rproc_list under RCU read lock
remoteproc: Fix NULL pointer dereference in rproc_virtio_notify
...
-----BEGIN PGP SIGNATURE-----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=I0vz
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 5.7-rc1.
Highlights:
- i915 enables Tigerlake by default
- i915 and amdgpu have initial OLED backlight support
[ Jani Nikula pipes up and points out that we've had a bunch of
"initial support" code for a long time already, but only now
Lyude made it actually work on real world machines ]
- vmwgfx add support to enable OpenGL 4 userspace
- zero length arrays are mostly removed.
Detailed summary:
new driver:
- tidss: TI Keystone platform display subsystem
core:
- new drm device warn macros
- mode config valid for memory constrained devices
- bridge bus format negotation
- consolidated fake vblank event handling
- dma_alloc related cleanups
- drop get_crtc callback
- dp: DP1.4 EDID corruption test
- EDID CEA detailed timings improvements
- relicense some code to dual GPL2/MIT
- convert core vblank support to per-crtc support
- rework drm_global_mutex
- bridge rework to allow omap_dss custom driver removeal
- remove drm_fb_helper connector interrfaces
- zero-length array removal
scheduler:
- support for modifying the sched list
- revert job distribution optimization
- helper to pick least loaded scheduler
- race condition fix
mst:
- various fixes
- remove register_connector callback
i915:
- uapi to allows userspace specific CS ring buffer sizes
- Tigerlake enablement patches + Tigerlake enabled by default
- new sysfs entries for engine properties
- display/logging refactors
- eDP/DP fixes for DPCD
- Gen7 back to aliasing-ppgtt
- Gen8+ irq refactor
- Avoid globals
- GEM locking fixes and simplifications
- Ice Lake and Elkhart Lake fixes and workarounds
- Baytrail/Haswell instability fix
- GVT - VFIO edid better support
amdgpu:
- Rework VM update handling in preparation for HMM support
- drm load/unload removal fixups
- USB-C PD firmware updates
- HDCP srm support
- Navi/renoir PM watermark fixes
- OLED panel support
- Optimize debugging vram access
- Use BACO for runtime pm
- DC clock programming optimizations and fixes
- PSP fw loading sequence updates
- Drop DRIVER_USE_AGP
- Remove legacy drm load and unload callbacks
- ACP Kconfig fix
- Lots of fixes across the driver
amdkfd:
- runtime pm support
- more gfx config details in amdgpu
radeon:
- drop DRIVER_USE_AGP
vmwgfx:
- Disable DMA when SEV encryption in use
- Shader Model 5 support - needed for GL4 support
msm:
- DPU resource manager refactor
- dpu using atomic global state
mediatek:
- MT8183 DPI support
etnaviv:
- out-of-bounds read fix
- expose feature flags for GC400 STM32MP1 SoC
- runtime suspend entry fix
- dma32 zone fix
hisilicon:
- mode selection fixes
meson:
- YUV420 support
lima:
- add support for heap buffers
tinydrm:
- removal of owner field
- explicit DT dependency removal
- YAML schema conversion
tegra:
- misc cleanups
tidss:
- new driver
virtio:
- better batching of notifications to host
- memory handling reworked
- shmem + gpu context fixes
hibmc:
- add gamma_set support
- improve DPMS support
pl111:
- Integrator IM-PD1 support
sun4i:
- LVDS support for A20 + A33
- DSI panel handling improvements"
* tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm: (1537 commits)
drm/i915/display: Fix mode private_flags comparison at atomic_check
drm/i915/gt: Stage the transfer of the virtual breadcrumb
drm/i915/gt: Select the deepest available parking mode for rc6
drm/i915: Avoid live-lock with i915_vma_parked()
drm/i915/gt: Treat idling as a RPS downclock event
drm/i915/gt: Cancel a hung context if already closed
drm/i915: Use explicit flag to mark unreachable intel_context
drm/amdgpu: don't try to reserve training bo for sriov (v2)
drm/amdgpu/smu11: add support for SMU AC/DC interrupts
drm/amdgpu/swSMU: handle manual AC/DC notifications
drm/amdgpu/swSMU: handle DC controlled by GPIO for navi1x
drm/amdgpu/swSMU: set AC/DC mode based on the current system state (v2)
drm/amdgpu/swSMU: correct the bootup power source for Navi1X (v2)
drm/amdgpu/swSMU: use the smu11 power source helper for navi1x
drm/amdgpu/smu11: add a helper to set the power source
drm/amd/swSMU: add callback to set AC/DC power source (v2)
drm/scheduler: fix rare NULL ptr race
drm/amdgpu: fix the coverage issue to clear ArcVPGRs
drm/amd/display: Fix pageflip event race condition for DCN.
drm/[radeon|amdgpu]: Remove HAINAN board from max_sclk override check
...
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci: Add support for sdmmc variant revision 2.0
- mmci_sdmmc: Improve support for busyend detection
- mmci_sdmmc: Fixup support for signal voltage switch
- mmci_sdmmc: Add support for tuning with delay block
- mtk-sd: Fix another SDIO irq issue
- sdhci: Disable native card detect when GPIO based type exist
- sdhci: Add option to defer request completion
- sdhci_am654: Add support to set a tap value per speed mode
- sdhci-esdhc-imx: Add support for i.MX8MM based variant
- sdhci-esdhc-imx: Fixup support for standard tuning on i.MX8 usdhc
- sdhci-esdhc-imx: Optimize for strobe/clock dll settings
- sdhci-esdhc-imx: Fixup support for system and runtime suspend/resume
- sdhci-iproc: Update regulator/bus-voltage management for bcm2711
- sdhci-msm: Prevent clock gating with PWRSAVE_DLL on broken variants
- sdhci-msm: Fix management of CQE during SDHCI reset
- sdhci-of-arasan: Add support for auto tuning on ZynqMP based platforms
- sdhci-omap: Add support for system suspend/resume
- sdhci-sprd: Add support for HW busy detection
- sdhci-sprd: Enable support host software queue
- sdhci-tegra: Add support for HW busy detection
- tmio/renesas_sdhi: Enforce retune after runtime suspend
- renesas_sdhi: Use manual tap correction for HS400 on some variants
- renesas_sdhi: Add support for manual correction of tap values for tunings
-----BEGIN PGP SIGNATURE-----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=gILc
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci:
* Add support for sdmmc variant revision 2.0
- mmci_sdmmc:
* Improve support for busyend detection
* Fixup support for signal voltage switch
* Add support for tuning with delay block
- mtk-sd:
* Fix another SDIO irq issue
- sdhci:
* Disable native card detect when GPIO based type exist
- sdhci:
* Add option to defer request completion
- sdhci_am654:
* Add support to set a tap value per speed mode
- sdhci-esdhc-imx:
* Add support for i.MX8MM based variant
* Fixup support for standard tuning on i.MX8 usdhc
* Optimize for strobe/clock dll settings
* Fixup support for system and runtime suspend/resume
- sdhci-iproc:
* Update regulator/bus-voltage management for bcm2711
- sdhci-msm:
* Prevent clock gating with PWRSAVE_DLL on broken variants
* Fix management of CQE during SDHCI reset
- sdhci-of-arasan:
* Add support for auto tuning on ZynqMP based platforms
- sdhci-omap:
* Add support for system suspend/resume
- sdhci-sprd:
* Add support for HW busy detection
* Enable support host software queue
- sdhci-tegra:
* Add support for HW busy detection
- tmio/renesas_sdhi:
* Enforce retune after runtime suspend
- renesas_sdhi:
* Use manual tap correction for HS400 on some variants
* Add support for manual correction of tap values for tunings"
* tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: cavium-octeon: remove nonsense variable coercion
mmc: mediatek: fix SDIO irq issue
mmc: mmci_sdmmc: Fix clear busyd0end irq flag
dt-bindings: mmc: Fix node name in an example
mmc: core: Re-work the code for eMMC sanitize
mmc: sdhci: use FIELD_GET for preset value bit masks
mmc: sdhci-of-at91: Display clock changes for debug purpose only
mmc: sdhci: iproc: Add custom set_power() callback for bcm2711
mmc: sdhci: am654: Use sdhci_set_power_and_voltage()
mmc: sdhci: at91: Use sdhci_set_power_and_voltage()
mmc: sdhci: milbeaut: Use sdhci_set_power_and_voltage()
mmc: sdhci: arasan: Use sdhci_set_power_and_voltage()
mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()
mmc: vub300: Use scnprintf() for avoiding potential buffer overflow
dt-bindings: mmc: synopsys-dw-mshc: fix clock-freq-min-max in example
sdhci: tegra: Enable MMC_CAP_WAIT_WHILE_BUSY host capability
sdhci: tegra: Implement Tegra specific set_timeout callback
mmc: sdhci-omap: Add Support for Suspend/Resume
mmc: renesas_sdhi: simplify execute_tuning
mmc: renesas_sdhi: Use BITS_PER_LONG helper
...
Core:
- Consolidation of the vDSO build infrastructure to address the
difficulties of cross-builds for ARM64 compat vDSO libraries by
restricting the exposure of header content to the vDSO build.
This is achieved by splitting out header content into separate
headers. which contain only the minimaly required information which is
necessary to build the vDSO. These new headers are included from the
kernel headers and the vDSO specific files.
- Enhancements to the generic vDSO library allowing more fine grained
control over the compiled in code, further reducing architecture
specific storage and preparing for adopting the generic library by PPC.
- Cleanup and consolidation of the exit related code in posix CPU timers.
- Small cleanups and enhancements here and there
Drivers:
- The obligatory new drivers: Ingenic JZ47xx and X1000 TCU support
- Correct the clock rate of PIT64b global clock
- setup_irq() cleanup
- Preparation for PWM and suspend support for the TI DM timer
- Expand the fttmr010 driver to support ast2600 systems
- The usual small fixes, enhancements and cleanups all over the place
-----BEGIN PGP SIGNATURE-----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=5o9G
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timekeeping and timer updates from Thomas Gleixner:
"Core:
- Consolidation of the vDSO build infrastructure to address the
difficulties of cross-builds for ARM64 compat vDSO libraries by
restricting the exposure of header content to the vDSO build.
This is achieved by splitting out header content into separate
headers. which contain only the minimaly required information which
is necessary to build the vDSO. These new headers are included from
the kernel headers and the vDSO specific files.
- Enhancements to the generic vDSO library allowing more fine grained
control over the compiled in code, further reducing architecture
specific storage and preparing for adopting the generic library by
PPC.
- Cleanup and consolidation of the exit related code in posix CPU
timers.
- Small cleanups and enhancements here and there
Drivers:
- The obligatory new drivers: Ingenic JZ47xx and X1000 TCU support
- Correct the clock rate of PIT64b global clock
- setup_irq() cleanup
- Preparation for PWM and suspend support for the TI DM timer
- Expand the fttmr010 driver to support ast2600 systems
- The usual small fixes, enhancements and cleanups all over the
place"
* tag 'timers-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (80 commits)
Revert "clocksource/drivers/timer-probe: Avoid creating dead devices"
vdso: Fix clocksource.h macro detection
um: Fix header inclusion
arm64: vdso32: Enable Clang Compilation
lib/vdso: Enable common headers
arm: vdso: Enable arm to use common headers
x86/vdso: Enable x86 to use common headers
mips: vdso: Enable mips to use common headers
arm64: vdso32: Include common headers in the vdso library
arm64: vdso: Include common headers in the vdso library
arm64: Introduce asm/vdso/processor.h
arm64: vdso32: Code clean up
linux/elfnote.h: Replace elf.h with UAPI equivalent
scripts: Fix the inclusion order in modpost
common: Introduce processor.h
linux/ktime.h: Extract common header for vDSO
linux/jiffies.h: Extract common header for vDSO
linux/time64.h: Extract common header for vDSO
linux/time32.h: Extract common header for vDSO
linux/time.h: Extract common header for vDSO
...
pwm_omap_dmtimer.h is used only:
- to typedef struct omap_dm_timer to pwm_omap_dmtimer
- for macro PWM_OMAP_DMTIMER_TRIGGER_OVERFLOW_AND_COMPARE
Rest of the file is pretty mush unsed. So reuse omap_dm_timer
and OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE in pwm-omap-dmtimer.c
and delete the header file.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Events are timestamped in EC time space, their timestamps need to be
converted in host time space.
The assumption is the time delta between when the interrupt is sent
by the EC and when it is receive by the host is a [small] constant.
This is not always true, even with hard-wired interrupt. To mitigate
worst offenders, add a median filter to weed out bigger than expected
delays.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
cros_ec_sensorhub registers a listener and query motion sense FIFO,
spread to iio sensors registers.
To test, we can use libiio:
iiod&
iio_readdev -u ip:localhost -T 10000 -s 25 -b 16 cros-ec-gyro | od -x
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
To better manage resources, store the number of sensors reported by
the EC.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The platform data header for OMAP remoteproc is no longer used for
anything post ti-sysc and DT conversion, so just remove it completely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-9-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
strobe-dll-delay-target is the delay cell add on the strobe line.
Strobe line the the uSDHC loopback read clock which is use in HS400
mode. Different strobe-dll-delay-target may need to set for different
board/SoC. If this delay cell is not set to an appropriate value,
we may see some read operation meet CRC error after HS400 mode select
which already pass the tuning.
This patch add the strobe-dll-delay-target setting in driver, so that
user can easily config this delay cell in dts file.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dm timer ops set_load() api allows to configure the load value and to
set the auto reload feature. But auto reload feature is independent of
load value and should be part of configuring pwm. This way pwm can be
disabled by disabling auto reload feature using set_pwm() so that the
current pwm cycle will be completed. Else pwm disabling causes the
cycle to be stopped abruptly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200305082715.15861-7-lokeshvutla@ti.com
omap_dm_timer_ops provide support to configure the pwm but there is no
support to get the current status. For configuring pwm it is advised to
check the current hw status instead of relying on pwm framework. So
implement a new timer ops to get the current status of pwm.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tony Lindgen <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200305082715.15861-6-lokeshvutla@ti.com
A selection of small fixes, mostly for drivers, that have arrived since
the merge window. None of them are earth shattering in themselves but
all useful for affected systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5iiroTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0ALxB/0TAEys4X1IxDku7N4E9vivlTQP+Yy5
LmJ7Oc+z1aCWX3LrpMa3M9JInnY44iahjariaZgcQ9GXXTO4rEoOSTVL99fXzj0h
wRS23p+h8GNFQ0s6Bzni8HSITz+vzCUJjYQe4i8iJIpQBRIErFSrqzB4uRGd7SPI
PIgYeTSA3rFuVvdAgijRg3hPTW2rpn328G/k35JpUNo9OdZ/v6NDQl1Sbg/FedFu
iY0feUaQ1FafHGkja/+OYN43bCraDo7Fo4COyF9cHGIJ8nBzMZJumhjgei26nviM
OQ15zRewFpnLGlK8ffPykrnynOhqo3GF7JbFWvI5pga/G5XzzLY8mi19
=bFsu
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A selection of small fixes, mostly for drivers, that have arrived
since the merge window. None of them are earth shattering in
themselves but all useful for affected systems"
* tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi_register_controller(): free bus id on error paths
spi: bcm63xx-hsspi: Really keep pll clk enabled
spi: atmel-quadspi: fix possible MMIO window size overrun
spi/zynqmp: remove entry that causes a cs glitch
spi: pxa2xx: Add CS control clock quirk
spi: spidev: Fix CS polarity if GPIO descriptors are used
spi: qup: call spi_qup_pm_resume_runtime before suspending
spi: spi-omap2-mcspi: Support probe deferral for DMA channels
spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x
The PRU-ICSS present on AM33xx/AM43xx/AM57xx has a very unique
SYSCFG register. The register follows the OMAP4-style SYSC_TYPE3
for Master Standby and Slave Idle, but also has two additional
unique fields - STANDBY_INIT and SUB_MWAIT. The STANDBY_INIT is
a control bit that is used to initiate a Standby sequence (when
set) and trigger a MStandby request to the SoC's PRCM module. This
same bit is also used to enable the OCP master ports (when cleared)
to allow the PRU cores to access any peripherals or memory beyond
the PRU subsystem. The SUB_MWAIT is a ready status field for the
external access.
Add support for this SYSC type. The STANDBY_INIT has to be set
during suspend, without which it results in a hang in the resume
sequence on AM33xx/AM43xx boards and requires a board reset to
come out of the hang. Any PRU applications requiring external
access are supposed to clear the STANDBY_INIT bit. Note that
the PRUSS context is lost during a suspend sequence because the
PRUSS module is reset and/or disabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated quirk define number and to use -ENODEV]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for am335x and am437x to properly enter deeper c-states in
cpuidle they must always call into the sleep33/43xx suspend code and
also sometimes invoke the wkup_m3_ipc driver. These are both controlled
by the pm33xx module so we must provide a method for the platform code
to call back into the module when it is available as the core cpuidle
ops that are invoked by the cpuidle-arm driver must remain as built in.
Extend the init platform op to take an idle function as an argument so
that we can use this to call into the pm33xx module for c-states that
need it. Also add a deinit op so we can unregister this idle function
from the PM core when the pm33xx module gets unloaded.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am335x and am437x can now make use of the generic cpuidle-arm driver.
This requires that we define init and suspend ops to be passed set as
the cpuidle ops for the SoC. These ops are invoked directly at the last
stage of the cpuidle-arm driver in order to allow low level platform
code to run and bring the CPU the rest of the way into it's desired idle
state. It is required that the CPUIDLE_METHOD_OF_DECLARE be called from
code that is built in so define these ops in pm33xx-core where the
always built-in portion of the PM code for these SoCs lives.
Additionally, although an soc_suspend function is already exposed by the
pm33xx platform code, it contains additional operations needed for full
SoC suspend beyond what is needed for a relatively simple CPU suspend
needed during cpuidle. To get around this introduce cpu_suspend ops to
be used by the am335x and am437x PM driver for the last stage of cpuidle
path.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The display subsystem (DSS) needs the child outputs disabled for reset.
In order to prepare to probe DSS without legacy platform data, let's
implement sysc_pre_reset_quirk_dss() similar to what we have for the
platform data with omap_dss_reset().
Note that we cannot directly use the old omap_dss_reset() without
platform data callbacks and updating omap_dss_reset() to understand
struct device. And we will be dropping omap_dss_reset() anyways when
all the SoCs are probing with device tree, so let's not mess with the
legacy code at all.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RTC modules on am3 and am4 need quirk handling to unlock and lock
them for reset so let's add the quirk handling based on what we already
have for legacy platform data. In later patches we will simply drop the
RTC related platform data and the old quirk handling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to know SoC type and features for cases where the same SoC
may be installed in various versions on the same board and would need
a separate dts file otherwise for the different variants.
For example, am3703 is pin compatible with omap3630, but has sgx and
iva accelerators disabled. We must not try to access the sgx or iva
module registers on am3703, and need to set the unavailable devices
disabled early.
Let's also detect omap3430 as that is needed for display subsystem
(DSS) reset later on, and GP vs EMU or HS devices. Further SoC
specific disabled device detection can be added as needed, such as
dra71x vs dra76x rtc and usb4.
Cc: Adam Ford <aford173@gmail.com>
Cc: André Hentschel <nerv@dawncrow.de>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nothing in the kernel includes the external header
<linux/platform_data/leds-kirkwood-ns2.h> so just push the
contents into the ns2 leds driver. If someone wants to use
platform data or board files to describe this device they
should be able to do so using GPIO machine descriptors but
in any case device tree should be the way forward for these
systems in all cases I can think of, and the driver already
supports that.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
RO and RW of EC may have different EC protocol version. If EC transitions
between RO and RW, but AP does not reboot (this is true for fingerprint
microcontroller / cros_fp, but not true for main ec / cros_ec), the AP
still uses the protocol version queried before transition, which can
cause problems. In the case of fingerprint microcontroller, this causes
AP to send the wrong version of EC_CMD_GET_NEXT_EVENT to RO in the
interrupt handler, which in turn prevents RO to clear the interrupt
line to AP, in an infinite loop.
Once an EC_HOST_EVENT_INTERFACE_READY is received, we know that there
might have been a transition between RO and RW, so re-query the protocol.
Signed-off-by: Yicheng Li <yichengli@chromium.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Replace with appropriate types.h.
Also there is no need to include device.h, but mutex.h.
For the pointers to unknown structures use forward declarations.
In the *.c files we need to include all headers that provide APIs
being used in the module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
ChromiumOS uses ACPI device with HID "GOOG0003" for power delivery
related events. The existing cros-usbpd-charger driver relies on these
events without ever actually receiving them on ACPI platforms. This is
because in the ChromeOS kernel trees, the GOOG0003 device is owned by an
ACPI driver that offers firmware updates to USB-C chargers.
Introduce a new platform driver under cros-ec, the ChromeOS embedded
controller, that handles these PD events and dispatches them
appropriately over a notifier chain to all drivers that use them.
On platforms that don't have the ACPI device defined, the driver gets
instantiated for ECs which support the EC_FEATURE_USB_PD feature bit,
and the notification events will get delivered using the MKBP event
handling mechanism.
Co-Developed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Jon Flatley <jflat@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-By: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+lTYPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3nQcQAJm91+6hZbmMjlBySGS7ISjYvOcrI/hMgiOl
uhhEP0Dcylvf9A9x3wcIbLwixe+2pvie9DQh2u5F80ShYimidtFi/2xCfuTb9fKu
sxxKjrXWyVKhkpW0z+tedY08ftVhkwwcyD4m2C7uVl6AwTP7c367vFeU7XjF2APn
drfgmgbjm8U3XbSyAqv+k6z6tyqaCnFM7vbPupSKHgHJ3mfByxOa+XyBN2RdgBbs
0KrVfbXGv80zFIFrMPwaWG7G52bu7K68nVdgy44MpKdRZ6QTjhnR+kerFxHsYgV4
bM55Fya52nTCSTGdKaQakDtKwbAUdCDTSkxgOHGcQoyFi0R/VaEUJtcysnvLbI6c
+n/yFIzGyEdXcvIzfv2SoDYhogw19I6RR/M9K5Ni29eazkDVYx2z3rI+2QYeqCiF
u7cq52gW6JLP0SI/9kuUrRFiR8v19Ixap7qokAxgqQwYB3NzT8a7WsYPkzdpDZGQ
ETSDFMyBWT6UvBe/HWkQluBabbet53rG8BF0OHFrQuMK0u/ieKgSGuTB9XN2djEW
PHMOMz2vhi+8XTfpkskhF2tTxlA/k4R6QwCdIMpIkMRVnVQCh1XdPr3Fi2NrgB+S
kIXHD4vV6zLYh04zHyKewSPHAXWgraFpg2qKnvL5+KWMTnW6QH+RNjOt9xKDNXOd
+iDXpOad
=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
On AM654, McSPI can only support 4K - 1 bytes per transfer when DMA is
enabled. Therefore populate master->max_transfer_size callback to
inform client drivers of this restriction when DMA channels are
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace with appropriate types.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace with appropriate types.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
The 'cros_ec' core driver is the common interface for the cros_ec
transport drivers to do the shared operations to register, unregister,
suspend, resume and handle_event. The interface is provided by including
the header 'include/linux/platform_data/cros_ec_proto.h', however, instead
of have the implementation of these functions in cros_ec_proto.c, it is in
'cros_ec.c', which is a different kernel module. Apart from being a bad
practice, this can induce confusions allowing the users of the cros_ec
protocol to call these functions.
The register, unregister, suspend, resume and handle_event functions
*should* only be called by the different transport drivers (i2c, spi, lpc,
etc.), so make this a bit less confusing by moving these functions from
the public in-kernel space to a private include in platform/chrome, and
then, the interface for cros_ec module and for the cros_ec_proto module is
clean.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
