When an XDP redirect happens before the link is ready, that
transmission will not finish and will timeout, causing an adapter
reset. If the redirects do not stop, the adapter will not stop
resetting.
Wait for the driver to signal that there's a carrier before allowing
transmissions to proceed.
Previous code was relying that when __IGC_DOWN is cleared, the NIC is
ready to transmit as all the queues are ready, what happens is that
the carrier presence will only be signaled later, after the watchdog
workqueue has a chance to run. And during this interval (between
clearing __IGC_DOWN and the watchdog running) if any transmission
happens the timeout is emitted (detected by igc_tx_timeout()) which
causes the reset, with the potential for the infinite loop.
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Closes: https://lore.kernel.org/netdev/0caf33cf6adb3a5bf137eeaa20e89b167c9986d5.camel@ericsson.com/
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to shared variables through hrtimer requires locking in order
to protect the variables because actions to write into these variables
(oper_gate_closed, admin_gate_closed, and qbv_transition) might potentially
occur simultaneously. This patch provides a locking mechanisms to avoid
such scenarios.
Fixes: 175c241288 ("igc: Fix TX Hang issue when QBV Gate is closed")
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230807205129.3129346-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In normal operation, each populated queue item has
next_to_watch pointing to the last TX desc of the packet,
while each cleaned item has it set to 0. In particular,
next_to_use that points to the next (necessarily clean)
item to use has next_to_watch set to 0.
When the TX queue is used both by an application using
AF_XDP with ZEROCOPY as well as a second non-XDP application
generating high traffic, the queue pointers can get in
an invalid state where next_to_use points to an item
where next_to_watch is NOT set to 0.
However, the implementation assumes at several places
that this is never the case, so if it does hold,
bad things happen. In particular, within the loop inside
of igc_clean_tx_irq(), next_to_clean can overtake next_to_use.
Finally, this prevents any further transmission via
this queue and it never gets unblocked or signaled.
Secondly, if the queue is in this garbled state,
the inner loop of igc_clean_tx_ring() will never terminate,
completely hogging a CPU core.
The reason is that igc_xdp_xmit_zc() reads next_to_use
before acquiring the lock, and writing it back
(potentially unmodified) later. If it got modified
before locking, the outdated next_to_use is written
pointing to an item that was already used elsewhere
(and thus next_to_watch got written).
Fixes: 9acf59a752 ("igc: Enable TX via AF_XDP zero-copy")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230717175444.3217831-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add TransmissionOverrun as per defined by IEEE 802.1Q Bridges.
TransmissionOverrun counter shall be incremented if the implementation
detects that a frame from a given queue is still being transmitted by
the MAC when that gate-close event for that queue occurs.
This counter is utilised by the Certification conformance test to
inform the user application whether any packets are currently being
transmitted on a particular queue during a gate-close event.
Intel Discrete I225/I226 have a mechanism to not transmit a packets if
the gate open time is insufficient for the packet transmission by setting
the Strict_End bit. Thus, it is expected for this counter to be always
zero at this moment.
Inspired from enetc_taprio_stats() and enetc_taprio_queue_stats(), now
driver also report the tx_overruns counter per traffic class.
User can get this counter by using below command:
1) tc -s qdisc show dev <interface> root
2) tc -s class show dev <interface>
Test Result (Before):
class mq :1 root
Sent 1289 bytes 20 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq :2 root
Sent 124 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq :3 root
Sent 46028 bytes 86 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
class mq :4 root
Sent 2596 bytes 14 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Test Result (After):
class taprio 100:1 root
Sent 8491 bytes 38 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Transmit overruns: 0
class taprio 100:2 root
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Transmit overruns: 0
class taprio 100:3 root
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Transmit overruns: 0
class taprio 100:4 root
Sent 994 bytes 11 pkt (dropped 0, overlimits 0 requeues 1)
backlog 0b 0p requeues 1
Transmit overruns: 0
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230714201428.1718097-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The insertion of an empty frame was introduced with
commit db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
it is possible to enable taprio offload with a basetime of 0.
However, the check if taprio offload is already enabled (and thus -EALREADY
should be returned for igc_save_qbv_schedule) still relied on
adapter->base_time > 0.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and base-time = 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
# The second call should fail with "Error: Device failed to setup taprio offload."
# But that only happens if base-time was != 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Only set adapter->taprio_offload_enable after validating the arguments.
Otherwise, it stays set even if the offload was not enabled.
Since the subsequent code does not get executed in case of invalid
arguments, it will not be read at first.
However, by activating and then deactivating another offload
(e.g. ETF/TX launchtime offload), taprio_offload_enable is read
and erroneously keeps the offload feature of the NIC enabled.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time -1000 \
sched-entry S 01 300000 \
flags 0x2
# IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register)
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Activate ETF offload
sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
hw 0
sudo tc qdisc add dev enp1s0 parent 6666:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload
# IGC_TQAVCTRL is 0x9 as expected
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Deactivate ETF offload again
sudo tc qdisc delete dev enp1s0 parent 6666:1
# IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the current implementation the flags adapter->qbv_enable
and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not
have the same meaning. The first one is used only to indicate
taprio offload (i.e. when igc_save_qbv_schedule was called),
while the second one corresponds to the Qbv mode of the hardware.
However, the second one is also used to support the TX launchtime
feature, i.e. ETF qdisc offload. This leads to situations where
adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED
is set. This is prone to confusion.
The rename should reduce this confusion. Since it is a pure
rename, it has no impact on functionality.
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IEEE 802.1Q does not have clear definitions of what constitutes an
SDU (Service Data Unit), but IEEE Std 802.3 clause 3.1.2 does define
the MAC service primitives and clause 3.2.7 does define the MAC Client
Data for Q-tagged frames.
It shows that the mac_service_data_unit (MSDU) does NOT contain the
preamble, destination and source address, or FCS. The MSDU does contain
the length/type field, MAC client data, VLAN tag and any padding
data (prior to the FCS).
Thus, the maximum 802.3 frame size that is allowed to be transmitted
should be QueueMaxSDU (MSDU) + 16 (6 byte SA + 6 byte DA + 4 byte FCS).
Fixes: 92a0dcb842 ("igc: offload queue max SDU from tc-taprio")
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a user schedules a Gate Control List (GCL) to close one of
the QBV gates while also transmitting a packet to that closed gate,
TX Hang will be happen. HW would not drop any packet when the gate
is closed and keep queuing up in HW TX FIFO until the gate is re-opened.
This patch implements the solution to drop the packet for the closed
gate.
This patch will also reset the adapter to perform SW initialization
for each 1st Gate Control List (GCL) to avoid hang.
This is due to the HW design, where changing to TSN transmit mode
requires SW initialization. Intel Discrete I225/6 transmit mode
cannot be changed when in dynamic mode according to Software User
Manual Section 7.5.2.1. Subsequent Gate Control List (GCL) operations
will proceed without a reset, as they already are in TSN Mode.
Step to reproduce:
DUT:
1) Configure GCL List with certain gate close.
BASE=$(date +%s%N)
tc qdisc replace dev $IFACE parent root handle 100 taprio \
num_tc 4 \
map 0 1 2 3 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE \
sched-entry S 0x8 500000 \
sched-entry S 0x4 500000 \
flags 0x2
2) Transmit the packet to closed gate. You may use udp_tai
application to transmit UDP packet to any of the closed gate.
./udp_tai -i <interface> -P 100000 -p 90 -c 1 -t <0/1> -u 30004
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Tested-by: Chwee Lin Choong <chwee.lin.choong@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove unnecessary delay during the TX ring configuration.
This will cause delay, especially during link down and
link up activity.
Furthermore, old SKUs like as I225 will call the reset_adapter
to reset the controller during TSN mode Gate Control List (GCL)
setting. This will add more time to the configuration of the
real-time use case.
It doesn't mentioned about this delay in the Software User Manual.
It might have been ported from legacy code I210 in the past.
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add condition to increase the qbv counter during taprio qbv
configuration only.
There might be a case when TC already been setup then user configure
the ETF/CBS qdisc and this counter will increase if no condition above.
Fixes: ae4fe46983 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Before requesting a packet transmission to be hardware timestamped,
check if the user has TX timestamping enabled. Fixes an issue that if
a packet was internally forwarded to the NIC, and it had the
SKBTX_HW_TSTAMP flag set, the driver would mark that timestamp as
skipped.
In reality, that timestamp was "not for us", as TX timestamp could
never be enabled in the NIC.
Checking if the TX timestamping is enabled earlier has a secondary
effect that when TX timestamping is disabled, there's no need to check
for timestamp timeouts.
We should only take care to free any pending timestamp when TX
timestamping is disabled, as that skb would never be released
otherwise.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the igc driver supports timestamping only one tx packet at a
time. During the transmission flow, the skb that requires hardware
timestamping is saved in adapter->ptp_tx_skb. Once hardware has the
timestamp, an interrupt is delivered, and adapter->ptp_tx_work is
scheduled. In igc_ptp_tx_work(), we read the timestamp register, update
adapter->ptp_tx_skb, and notify the network stack.
While the thread executing the transmission flow (the user process
running in kernel mode) and the thread executing ptp_tx_work don't
access adapter->ptp_tx_skb concurrently, there are two other places
where adapter->ptp_tx_skb is accessed: igc_ptp_tx_hang() and
igc_ptp_suspend().
igc_ptp_tx_hang() is executed by the adapter->watchdog_task worker
thread which runs periodically so it is possible we have two threads
accessing ptp_tx_skb at the same time. Consider the following scenario:
right after __IGC_PTP_TX_IN_PROGRESS is set in igc_xmit_frame_ring(),
igc_ptp_tx_hang() is executed. Since adapter->ptp_tx_start hasn't been
written yet, this is considered a timeout and adapter->ptp_tx_skb is
cleaned up.
This patch fixes the issue described above by adding the ptp_tx_lock to
protect access to ptp_tx_skb and ptp_tx_start fields from igc_adapter.
Since igc_xmit_frame_ring() called in atomic context by the networking
stack, ptp_tx_lock is defined as a spinlock, and the irq safe variants
of lock/unlock are used.
With the introduction of the ptp_tx_lock, the __IGC_PTP_TX_IN_PROGRESS
flag doesn't provide much of a use anymore so this patch gets rid of it.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Guarantee that when probe() is run again, PTM and PCI busmaster will be
in the same state as it was if the driver was never loaded.
Avoid an i225/i226 hardware issue that PTM requests can be made even
though PCI bus mastering is not enabled. These unexpected PTM requests
can crash some systems.
So, "force" disable PTM and busmastering before removing the driver,
so they can be re-enabled in the right order during probe(). This is
more like a workaround and should be applicable for i225 and i226, in
any platform.
Fixes: 1b5d73fb86 ("igc: Enable PCIe PTM")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
High XDP load triggers the netdev watchdog:
|NETDEV WATCHDOG: enp3s0 (igc): transmit queue 2 timed out
The reason is the Tx queue transmission start (txq->trans_start) is not updated
in XDP code path. Therefore, add it for all XDP transmission functions.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZGKqEAAKCRDbK58LschI
g6LYAQDp1jAszCOkmJ8VUA0ZyC5NAFDv+7y9Nd1toYWYX1btzAEAkf8+5qBJ1qmI
P5M0hjMTbH4MID9Aql10ZbMHheyOBAo=
=NUQM
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-05-16
We've added 57 non-merge commits during the last 19 day(s) which contain
a total of 63 files changed, 3293 insertions(+), 690 deletions(-).
The main changes are:
1) Add precision propagation to verifier for subprogs and callbacks,
from Andrii Nakryiko.
2) Improve BPF's {g,s}setsockopt() handling with wrong option lengths,
from Stanislav Fomichev.
3) Utilize pahole v1.25 for the kernel's BTF generation to filter out
inconsistent function prototypes, from Alan Maguire.
4) Various dyn-pointer verifier improvements to relax restrictions,
from Daniel Rosenberg.
5) Add a new bpf_task_under_cgroup() kfunc for designated task,
from Feng Zhou.
6) Unblock tests for arm64 BPF CI after ftrace supporting direct call,
from Florent Revest.
7) Add XDP hint kfunc metadata for RX hash/timestamp for igc,
from Jesper Dangaard Brouer.
8) Add several new dyn-pointer kfuncs to ease their usability,
from Joanne Koong.
9) Add in-depth LRU internals description and dot function graph,
from Joe Stringer.
10) Fix KCSAN report on bpf_lru_list when accessing node->ref,
from Martin KaFai Lau.
11) Only dump unprivileged_bpf_disabled log warning upon write,
from Kui-Feng Lee.
12) Extend test_progs to directly passing allow/denylist file,
from Stephen Veiss.
13) Fix BPF trampoline memleak upon failure attaching to fentry,
from Yafang Shao.
14) Fix emitting struct bpf_tcp_sock type in vmlinux BTF,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (57 commits)
bpf: Fix memleak due to fentry attach failure
bpf: Remove bpf trampoline selector
bpf, arm64: Support struct arguments in the BPF trampoline
bpftool: JIT limited misreported as negative value on aarch64
bpf: fix calculation of subseq_idx during precision backtracking
bpf: Remove anonymous union in bpf_kfunc_call_arg_meta
bpf: Document EFAULT changes for sockopt
selftests/bpf: Correctly handle optlen > 4096
selftests/bpf: Update EFAULT {g,s}etsockopt selftests
bpf: Don't EFAULT for {g,s}setsockopt with wrong optlen
libbpf: fix offsetof() and container_of() to work with CO-RE
bpf: Address KCSAN report on bpf_lru_list
bpf: Add --skip_encoding_btf_inconsistent_proto, --btf_gen_optimized to pahole flags for v1.25
selftests/bpf: Accept mem from dynptr in helper funcs
bpf: verifier: Accept dynptr mem as mem in helpers
selftests/bpf: Check overflow in optional buffer
selftests/bpf: Test allowing NULL buffer in dynptr slice
bpf: Allow NULL buffers in bpf_dynptr_slice(_rw)
selftests/bpf: Add testcase for bpf_task_under_cgroup
bpf: Add bpf_task_under_cgroup() kfunc
...
====================
Link: https://lore.kernel.org/r/20230515225603.27027-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC hardware RX timestamping mechanism adds an optional tailored
header before the MAC header containing packet reception time. Optional
depending on RX descriptor TSIP status bit (IGC_RXDADV_STAT_TSIP). In
case this bit is set driver does offset adjustments to packet data start
and extracts the timestamp.
The timestamp need to be extracted before invoking the XDP bpf_prog,
because this area just before the packet is also accessible by XDP via
data_meta context pointer (and helper bpf_xdp_adjust_meta). Thus, an XDP
bpf_prog can potentially overwrite this and corrupt data that we want to
extract with the new kfunc for reading the timestamp.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182465791.616355.2583922957423587914.stgit@firesoul
This implements XDP hints kfunc for RX-hash (xmo_rx_hash).
The HW rss hash type is handled via mapping table.
This igc driver (default config) does L3 hashing for UDP packets
(excludes UDP src/dest ports in hash calc). Meaning RSS hash type is
L3 based. Tested that the igc_rss_type_num for UDP is either
IGC_RSS_TYPE_HASH_IPV4 or IGC_RSS_TYPE_HASH_IPV6.
This patch also updates AF_XDP zero-copy function igc_clean_rx_irq_zc()
to use the xdp_buff wrapper struct igc_xdp_buff.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182465285.616355.2701740913376314790.stgit@firesoul
Driver specific metadata data for XDP-hints kfuncs are propagated via tail
extending the struct xdp_buff with a locally scoped driver struct.
Zero-Copy AF_XDP/XSK does similar tricks via struct xdp_buff_xsk. This
xdp_buff_xsk struct contains a CB area (24 bytes) that can be used for
extending the locally scoped driver into. The XSK_CHECK_PRIV_TYPE define
catch size violations build time.
The changes needed for AF_XDP zero-copy in igc_clean_rx_irq_zc()
is done in next patch, because the member rx_desc isn't available
at this point.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464779.616355.3761989884165609387.stgit@firesoul
When function igc_rx_hash() was introduced in v4.20 via commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers"), the
hardware wasn't configured to provide RSS hash, thus it made sense to not
enable net_device NETIF_F_RXHASH feature bit.
The NIC hardware was configured to enable RSS hash info in v5.2 via commit
2121c2712f ("igc: Add multiple receive queues control supporting"), but
forgot to set the NETIF_F_RXHASH feature bit.
The original implementation of igc_rx_hash() didn't extract the associated
pkt_hash_type, but statically set PKT_HASH_TYPE_L3. The largest portions of
this patch are about extracting the RSS Type from the hardware and mapping
this to enum pkt_hash_types. This was based on Foxville i225 software user
manual rev-1.3.1 and tested on Intel Ethernet Controller I225-LM (rev 03).
For UDP it's worth noting that RSS (type) hashing have been disabled both for
IPv4 and IPv6 (see IGC_MRQC_RSS_FIELD_IPV4_UDP + IGC_MRQC_RSS_FIELD_IPV6_UDP)
because hardware RSS doesn't handle fragmented pkts well when enabled (can
cause out-of-order). This results in PKT_HASH_TYPE_L3 for UDP packets, and
hash value doesn't include UDP port numbers. Not being PKT_HASH_TYPE_L4, have
the effect that netstack will do a software based hash calc calling into
flow_dissect, but only when code calls skb_get_hash(), which doesn't
necessary happen for local delivery.
For QA verification testing I wrote a small bpftrace prog:
[0] https://github.com/xdp-project/xdp-project/blob/master/areas/hints/monitor_skb_hash_on_dev.bt
Fixes: 2121c2712f ("igc: Add multiple receive queues control supporting")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464270.616355.11391652654430626584.stgit@firesoul
The check introduced in the commit a5fd39464a ("igc: Lift TAPRIO schedule
restriction") can detect a false positive error in some corner case.
For instance,
tc qdisc replace ... taprio num_tc 4
...
sched-entry S 0x01 100000 # slot#1
sched-entry S 0x03 100000 # slot#2
sched-entry S 0x04 100000 # slot#3
sched-entry S 0x08 200000 # slot#4
flags 0x02 # hardware offload
Here the queue#0 (the first queue) is on at the slot#1 and #2,
and off at the slot#3 and #4. Under the current logic, when the slot#4
is examined, validate_schedule() returns *false* since the enablement
count for the queue#0 is two and it is already off at the previous slot
(i.e. #3). But this definition is truely correct.
Let's fix the logic to enforce a strict validation for consecutively-opened
slots.
Fixes: a5fd39464a ("igc: Lift TAPRIO schedule restriction")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (igc)
This series contains updates to igc driver only.
Muhammad adds tracking and reporting of QBV config errors.
Tan Tee adds support for configuring max SDU for each Tx queue.
Sasha removes check for alternate media as only one media type is
supported.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Clean up and optimize watchdog task
igc: offload queue max SDU from tc-taprio
igc: Add qbv_config_change_errors counter
====================
Link: https://lore.kernel.org/r/20230307221332.3997881-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i225/i226 parts used only one media type copper. The copper media type is
not replaceable. Clean up the code accordingly, and remove the obsolete
media replacement and reset options.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for configuring the max SDU for each Tx queue.
If not specified, keep the default.
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ConfigChangeError(qbv_config_change_errors) when user try to set the
AdminBaseTime to past value while the current GCL is still running.
The ConfigChangeError counter should not be increased when a gate control
list is scheduled into the future.
User can use "ethtool -S <interface> | grep qbv_config_change_errors"
command to check the counter values.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 2 classes of in-tree drivers currently:
- those who act upon struct tc_taprio_sched_entry :: gate_mask as if it
holds a bit mask of TXQs
- those who act upon the gate_mask as if it holds a bit mask of TCs
When it comes to the standard, IEEE 802.1Q-2018 does say this in the
second paragraph of section 8.6.8.4 Enhancements for scheduled traffic:
| A gate control list associated with each Port contains an ordered list
| of gate operations. Each gate operation changes the transmission gate
| state for the gate associated with each of the Port's traffic class
| queues and allows associated control operations to be scheduled.
In typically obtuse language, it refers to a "traffic class queue"
rather than a "traffic class" or a "queue". But careful reading of
802.1Q clarifies that "traffic class" and "queue" are in fact
synonymous (see 8.6.6 Queuing frames):
| A queue in this context is not necessarily a single FIFO data structure.
| A queue is a record of all frames of a given traffic class awaiting
| transmission on a given Bridge Port. The structure of this record is not
| specified.
i.o.w. their definition of "queue" isn't the Linux TX queue.
The gate_mask really is input into taprio via its UAPI as a mask of
traffic classes, but taprio_sched_to_offload() converts it into a TXQ
mask.
The breakdown of drivers which handle TC_SETUP_QDISC_TAPRIO is:
- hellcreek, felix, sja1105: these are DSA switches, it's not even very
clear what TXQs correspond to, other than purely software constructs.
Only the mqprio configuration with 8 TCs and 1 TXQ per TC makes sense.
So it's fine to convert these to a gate mask per TC.
- enetc: I have the hardware and can confirm that the gate mask is per
TC, and affects all TXQs (BD rings) configured for that priority.
- igc: in igc_save_qbv_schedule(), the gate_mask is clearly interpreted
to be per-TXQ.
- tsnep: Gerhard Engleder clarifies that even though this hardware
supports at most 1 TXQ per TC, the TXQ indices may be different from
the TC values themselves, and it is the TXQ indices that matter to
this hardware. So keep it per-TXQ as well.
- stmmac: I have a GMAC datasheet, and in the EST section it does
specify that the gate events are per TXQ rather than per TC.
- lan966x: again, this is a switch, and while not a DSA one, the way in
which it implements lan966x_mqprio_add() - by only allowing num_tc ==
NUM_PRIO_QUEUES (8) - makes it clear to me that TXQs are a purely
software construct here as well. They seem to map 1:1 with TCs.
- am65_cpsw: from looking at am65_cpsw_est_set_sched_cmds(), I get the
impression that the fetch_allow variable is treated like a prio_mask.
This definitely sounds closer to a per-TC gate mask rather than a
per-TXQ one, and TI documentation does seem to recomment an identity
mapping between TCs and TXQs. However, Roger Quadros would like to do
some testing before making changes, so I'm leaving this driver to
operate as it did before, for now. Link with more details at the end.
Based on this breakdown, we have 5 drivers with a gate mask per TC and
4 with a gate mask per TXQ. So let's make the gate mask per TXQ the
opt-in and the gate mask per TC the default.
Benefit from the TC_QUERY_CAPS feature that Jakub suggested we add, and
query the device driver before calling the proper ndo_setup_tc(), and
figure out if it expects one or the other format.
Link: 2023020200.2679603-15-vladimir.oltean@nxp.com/#25193204
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Siddharth Vadapalli <s-vadapalli@ti.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
I225 have limitation when programming the BaseTime register which required
a power cycle of the controller. This limitation already lifted in I226.
This patch removes the restriction so that when user configure/remove any
TSN mode, it would not go into power cycle reset adapter.
How to test:
Schedule any gate control list configuration or delete it.
Example:
1)
BASE_TIME=$(date +%s%N)
tc qdisc replace dev $interface_name parent root handle 100 taprio \
num_tc 4 \
map 3 1 0 2 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE_TIME \
sched-entry S 0F 1000000 \
flags 0x2
2) tc qdisc del dev $intername_name root
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make reset task only executes for i225 and Qbv disabling to allow
i226 configure for 2nd GCL without resetting the adapter.
In i226, Tx won't hang if there is a GCL is already running, so in
this case we don't need to set FutScdDis bit.
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the Qbv BaseTime restriction for I226 so that the BaseTime can be
scheduled to the future time. A new register bit of Tx Qav Control
(Bit-7: FutScdDis) was introduced to allow I226 scheduling future time as
Qbv BaseTime and not having the Tx hang timeout issue.
Besides, according to datasheet section 7.5.2.9.3.3, FutScdDis bit has to
be configured first before the cycle time and base time.
Indeed the FutScdDis bit is only active on re-configuration, thus we have
to set the BASET_L to zero and then only set it to the desired value.
Please also note that the Qbv configuration flow is moved around based on
the Qbv programming guideline that is documented in the latest datasheet.
Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
