From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit
latency being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Without additional HostVM Latency, Renoir takes 2us longer to exit
self-refresh. This causes underflow in certain cases.
[How]
Add table for Renoir with updated sr exit latencies for WM set A.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How & Why]
Allow clk_mgr functions to be reused by making then non-static
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While booting into OS, driver updates DPP/DISP CLKs.
But init clock value is zero which is invalid.
[How]
Get current clocks value to update init clocks.
To avoid underflow.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 2208f39c75.
It caused a regression in internal FPGA tests.
Signed-off-by: Eric Bernstein <Eric.Bernstein@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After removing added latency for HostVM by default, DDR4 sr exit
latencies were no longer large enough for some panels and caused
underflow.
[How]
Add 1us to sr enter/exit watermark.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Blue screen when PNP with multiple monitor or hotplug external monitor when playing video
due to dpp dto isn't programmed properly.
If lower dpp clock, dpp dto need to be programmed first, and actual dpp clk not avalable yet.
[How]
set dpp dto as per request clk for lower case before dpp clk update, and after dpp clk updated
set dpp dto again with actual dpp clk.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently if VBIOSSMC_Result_UnknownCmd is returned as result of smu msg
there is no way to know. Put 1 in param so if 1 is returned, this unknown case is handled.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpp dto phase and modulo are programmed with actual dpp global clk
and pipe clk. Need to use actual dpp clk to prgoram dpp dto modulo
to get more accuracy ratio.
[How]
assign actual dpp clk to dccg for dpp modulo programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Actual dpp/disp clock PMFW set are always equal or more than requested.
Need to cache the actual clock for debugging purpose.
[How]
Add actuall dpp/disp clk in clock manager and save it when set clocks.
Add an ASSERT in case of actual clock less than requested.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The intended use is to force PSR into active state and ignore all
events until explicit EXIT.
A new event force_static is added to power module. It is then sent
to FW.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add proper FP_START/END handling and adjust Makefiles per
previous asics.
v2: fix up harder.
v3: fix clkmgr Makefile for dcn30
v4: fix old gcc handling is only required for x86
Build-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect values were resulting in flash lines
when MPO was enabled and system was left idle.
[How]
Increase min clk values only when MPO is enabled
and display is active to not affect S3 power.
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate config option at this point.
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check chip family also to avoid wrong identification.
V2: use the correct macro without AMDGPU prefix
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently disable 48mhz debug option only disables on boot.
Need to put option check in update_clocks as well to make it
affect more areas.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable Memory Access at Last Level (MALL) feature for display.
v2: squash in 64 bit division fixes
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display Core support for green_sardine
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dc for vangogh support.
v2: fix compilation without DCN 301 set.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sometimes CRTCs can be disabled due to display unplugging or temporarily
transition in the userspace; in these circumstances, DCE tries to set
the minimum clock threshold. When we have this situation, the function
bw_calcs is invoked with number_of_displays set to zero, making DCE set
dispclk_khz and sclk_khz to zero. For these reasons, we have seen some
ATOM bios errors that look like:
[drm:atom_op_jump [amdgpu]] *ERROR* atombios stuck in loop for more than
5secs aborting
[drm:amdgpu_atom_execute_table_locked [amdgpu]] *ERROR* atombios stuck
executing EA8A (len 761, WS 0, PS 0) @ 0xEABA
[How]
This error happens due to an attempt to optimize the bandwidth using the
sclk, and the dispclk clock set to zero. Technically we handle this in
the function dce112_set_clock, but we are not considering the case that
this value is set to zero. This commit fixes this issue by ensuring that
we never set a minimum value below the minimum clock threshold.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 78fe9f6394 ("drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions")
added a call to rn_vbios_smu_get_smu_version() to set clk_mgr->smu_ver.
That field is initialized prior to the if-statement, already.
Fixes: 78fe9f6394 (drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions)
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sung Lee <sung.lee@amd.com>
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
linux-next kernel test robot reported the following problem:
warning: no previous prototype for 'dce60_get_dp_ref_freq_khz' [-Wmissing-prototypes]
[How]
mark dce60_get_dp_ref_freq_khz() as static
Fixes: 3ecb3b794e "drm/amd/display: dc/clk_mgr: add support for SI parts (v2)"
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the load processes for Renoir, our display code needs to retrieve
the SMU clock and voltage table, however, this operation can fail which
means that we have to check this scenario. Currently, we are not
handling this case properly and as a result, we have seen the following
dmesg log during the boot:
RIP: 0010:rn_clk_mgr_construct+0x129/0x3d0 [amdgpu]
...
Call Trace:
dc_clk_mgr_create+0x16a/0x1b0 [amdgpu]
dc_create+0x231/0x760 [amdgpu]
This commit fixes this issue by checking the return status retrieved
from the clock table before try to populate any bandwidth.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.
[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds ARM64 support into the DCN. This mainly enables support
for Navi graphics cards. The dcn10 changes haven't been tested,
since I don't have the relevant hardware available, but there
is no way to conditionally disable them, so I've done them anyway.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Changelog
[Why]
After commit c69dd2d "drm/amd/display: Refactor clk_mgr functions"
dc/clk_mgr requires these changes to add SI parts support
Necessary to avoid hitting default: ASSERT(0); /* Unknown Asic */
that would cause kernel freeze
[How]
Add case statement for FAMILY_SI chipsets
(v2) Changelog
[Why]
DCE6 has no DPREFCLK_CNTL register
[How]
Add DCE6 specific macros definitions for CLK registers and masks
Add DCE6 specific dce60/dce60_clk_mgr.c for DCE6 customization
Code style: reuse all the public functions in dce100/dce_clk_mgr.h header
Code style: use dce60_* static functions as per other DCE implementations
Add dce60_get_dp_ref_freq_khz() w/o using DPREFCLK_CNTL register
Use dce60_get_dp_ref_freq_khz() function in dce60_funcs
Add DCE6 specific dce60_clk_mgr_construct
dc/clk_mgr/dce_clk_mgr.c: use dce60_clk_mgr_construct for FAMILY_SI chipsets
Add Makefile rules for dce60_clk_mgr.o target conditional to CONFIG_DRM_AMD_DC_SI
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dcn3_update_clocks there are situations where dppclk is not
lowered (i.e. stays the same), but DTO still needs to be increased
before we program pipe frontend (i.e. in prepare_bandwidth). If we
don't program the new DTO value before we program the pipe,
we will underflow as soon as the pipe lock is released until the
next call to dcn3_update_clocks where the DTO is updated.
[How]
Remove dppclk check before programming new DTO value.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix below warnings reported by coccicheck:
./drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr.c:557:2-7: WARNING: NULL check before some freeing functions is not needed.
Fixes: 4d55b0dd1c ("drm/amd/display: Add DCN3 CLK_MGR")
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when ppt disabled, the watermark doesn't get fine tune causing
underflow.
[How]
It is a temporary solution to reduce sr_xxx_time by 3 us when ppt
disable.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to be able to see SMU messages sent and their responses
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we don't explicitly send a request for a minimum PHYCLK, and
we hope that the dependencies other clocks have will raise PHYCLK when
needed.
[How]
- new clk_mgr function to keep track of PHYCLK requirements
- request maximum requirement across all links
- remove PHYCLK from clock state comparator, as it doesn't come from DML
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU may return error code to driver, but driver only check if response
is OK.
[How]
Check SMU response instead of reg_wait, assert in case of reponse isn't
OK.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to keep the same buffer allocated for use during multiple
hardware initializations.
[How]
- allocate gpu memory buffer on clock manager construct
- free gpu memory buffer on clock manager destruct
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We try to to change new_clocks->dppclk_khz to 100000 when
new_clocks->dppclk_khz is 0
[How]
Don't change new_clocks->dppclk_khz value when new_clocks->dppclk_khz is
0
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is using pixelclk AVFS for dppclk, that would cause issue.
[How]
To use dispclk AVFS for both dispclk and dppclk. There would choose
dppclk for request voltage when dispclk wouldn't be updated case. If
dispclk need to be updated, then it'll choose the bigger one from dppclk
and dispclk for request voltage.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN3 block
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver already get display clock from SMU base on MHz, but driver read
again and mutiple 1000 cause wait loop value is overflow.
[How]
remove coding error
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As it stands, psr has feature flags in dm, stream, and link. Most are
not defined well enough, and different dm layers have different uses for
these same flags.
[How]
We define a new structure called psr_settings in dc_link that will hold
the following psr feature flags:
psr_feature_enable - psr is supported
psr_allow_active - psr is currently active
psr_version - internal psr version supported
psr_frame_capture_indication_req
psr_sdp_transmit_line_num_deadline
The last two flags were moved out of the power module
for the purposes of consolidating psr flags.
Their use is already well-defined.
Psr caps reported by sink will also be stored in dc_link,
in dpcd_caps.psr_caps.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable dp_ref_clk_khz is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>