[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DSCL memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
1. Write to DSCL_MEM_PWR_FORCE to put memory to shutdown when DSCL is not
used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
only apply multiple display power optimization in case there are more
than one internal display.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, DMCU is no longer used. In these cases, some DMCU
memory should be completely powered off to save power.
[How]
1. Set DMCU_ERAM_MEM_PWR_FORCE to shutdown memory when DMCU is not in
use
2. Added a debug option to allow this behaviour to be turned off
3. Set all memory low power debug options to off first, to not
immediately cause problems
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should use int for counting variable
[How]
Change type from bool to uint32_t
Signed-off-by: Raymond Yang <rayyang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Check if the eDP sink supports the dynamic backlight control
[How]
Query the dynamic backlight capability in DPCD (eDP case only)
Signed-off-by: Roy Chan <roy.chan@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Actual dpp/disp clock PMFW set are always equal or more than requested.
Need to cache the actual clock for debugging purpose.
[How]
Add actuall dpp/disp clk in clock manager and save it when set clocks.
Add an ASSERT in case of actual clock less than requested.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The OPTC memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Set ODM_MEM_UNASSIGNED_PWR_MODE to shutdown memory when unassigned
2. Set ODM_MEM_VBLANK_PWR_MODE to light sleep mode when in vblank
3. Added a debug option to allow this behaviour to be turned off
4. Restructured debug options to use a bitfield in a way that's more clear
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPC memory blocks in DCN3 should be powered down completely when
they are not in use. This will reduce power consumption.
[How]
This commits changes behaviour for dcn3 and does the following:
1. Write to MPC_RMU<X>_LOW_PWR_MODE and MPCC_OGAM_MEM_LOW_PWR_MODE to
automatically shut down memory when not in use
2. mpc3_power_on_shaper_3dlut and mpc3_power_on_ogam_lut are called
to disable force power on when configuration finishes
3. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Functions (disable_all_writeback_pipes_for_stream &
dc_enable_stereo & dc_post_update_surfaces_to_stream)
always return true, there is no need to keep the return value.
This change is to make the code a bit more readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
At the moment, some tests are failing because cur_link_settings is
invalid. As a workaround, add an option to force dio disable.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
with eDP + DP, each display use one pipe. after DP unplugged, eDP switch
from one pipe to two pipes -- pipe split. dpp1_cm_set_regamma_pwl will
be executed too. The duration from switch single pipe to dual pipes is a
little long which could let eDP enter PSR mode. upon two pipes for eDP
are setup, eDP PHY is disabled. front pipe is not really running to
fetch data from frame buffer. i.e., dchubp is not in normal working
status. execution of hubbub1_wm_change_req_wa may cause p-state warning.
[How]
disable eDP PSR before dc_commit_state. psr is disabled when execute
hubbub1_wm_change_req_wa.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement an interface to obtain plane size caps
[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register key for AE or QA do regression test. New edid status for
check.
[How]
Add register key edid_read_retry_times.
Add new edid status EDID_FALL_BACK.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
