Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d393 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple internal mdio bus creation from serdes
configuration, as a prerequisite to offloading
serdes configuration to a different module.
Group together mdio bus creation routines, cleanup.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple level MAC configuration based on phy interface type
from general port configuration.
Group together MAC and link configuration code.
Decouple external mdio bus creation from interface type
parsing. No longer return an (unhandled) error code when
phy_node not found, use phy_node to indicate whether the
port has a phy or not. No longer fall-through when serdes
configuration fails for the link modes that require
internal link configuration.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When packets are received on the error queue, this function under
net_ratelimit():
netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");
does not get printed. Instead we only see:
[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed
Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new group of devlink traps - PARSER_ERROR_DROPS.
This consists of registering the array of parser error drops supported,
controlling their action through the .trap_group_action_set() callback
and reporting an erroneous skb received on the error queue
appropriately.
DPAA2 devices do not support controlling the action of independent
parser error traps, thus the .trap_action_set() callback just returns an
EOPNOTSUPP while .trap_group_action_set() actually notifies the hardware
what it should do with a frame marked as having a header error.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support in dpaa2-eth for devlink. For the moment, just
register the device with devlink, add the corresponding devlink port and
implement the .info_get() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
mpc52xx_fec_stop() uses in_interrupt() to check if it is safe to sleep. All
callers run in well defined contexts.
Pass an argument from the callers indicating whether it is safe to sleep.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a null-check for _pcs_, but it is being dereferenced
prior to this null-check. So, if _pcs_ can actually be null,
then there is a potential null pointer dereference that should
be fixed by null-checking _pcs_ before being dereferenced.
Addresses-Coverity-ID: 1497159 ("Dereference before null check")
Fixes: 94ae899b20 ("dpaa2-mac: add PCS support through the Lynx module")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SHARED_FS is enabled on a DPNI object the flow steering tables are
shared between all the traffic classes. Modify the driver so that we
only add a new flow steering entry on the TC#0 when this new option is
enabled.
Signed-off-by: Ionut-robert Aron <ionut-robert.aron@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to dpaa2_eth_link_state_update() is a leftover from the time
when on DPAA2 platforms the PHYs were started at boot time so when an
ifconfig was issued on the associated interface, the link status needed
to be checked directly from the ndo_open() callback.
This is not needed anymore since we are now properly integrated with the
PHY layer thus a link interrupt will come directly from the PHY
eventually without the need to call the sync function.
Fix this up by removing the call to dpaa2_eth_link_state_update().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to check if both the MDIO controller node and its
child node, the PCS device, are available since there is no chance that
the child node would be enabled when the parent it's not.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the support for TBF offload, the improper command version
was added even though the command format is for the V2 of
dpni_set_tx_shaping(). This does not affect the functionality of TBF
since the only change between these two versions is the addition of the
exceeded parameters which are not used in TBF. Still, fix the bug so
that we keep things in sync.
Fixes: 39344a8962 ("dpaa2-eth: add API for Tx shaping")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe. On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present. Since 0f183fd151 (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.
Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include PCS support in the dpaa2-eth driver by integrating it with the
new Lynx PCS module. There is not much to talk about in terms of changes
needed in the dpaa2-eth driver since the only steps necessary are to
find the MDIO device representing the PCS, register it to the Lynx PCS
module and then let phylink know if its existence also.
After this, the PCS callbacks will be treated directly by Lynx, without
interraction from dpaa2-eth's part.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix below sparse warning in dpmac.c.
warning: cast to restricted __le64
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add PTP sync packet one-step timestamping support.
Before egress, one-step timestamping enablement needs,
- Enabling timestamp and FAS (Frame Annotation Status) in
dpni buffer layout.
- Write timestamp to frame annotation and set PTP bit in
FAS to mark as one-step timestamping event.
- Enabling one-step timestamping by dpni_set_single_step_cfg()
API, with offset provided to insert correction time on frame.
The offset must respect all MAC headers, VLAN tags and other
protocol headers accordingly. The correction field update can
consider delays up to one second. So PTP frame needs to be
filtered and parsed, and written timestamp into Sync frame
originTimestamp field.
The operation of API dpni_set_single_step_cfg() has to be done
when no one-step timestamping frames are in flight. So we have
to make sure the last one-step timestamping frame has already
been transmitted on hardware before starting to send the current
one. The resolution is,
- Utilize skb->cb[0] to mark timestamping request per packet.
If it is one-step timestamping PTP sync packet, queue to skb queue.
If not, transmit immediately.
- Schedule a work to transmit skbs in skb queue.
- mutex lock is used to ensure the last one-step timestamping packet
has already been transmitted on hardware through TX confirmation queue
before transmitting current packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation for next hardware one-step timestamping
support. For DPAA2, the one step timestamping configuration on
hardware registers has to be done when there is no one-step timestamping
packet in flight. So we will have to use workqueue and skb queue
for such packets transmitting, to make sure waiting the last packet has
already been sent on hardware, and starting to transmit the current one.
So the tx timestamping flag in private data may not reflect the actual
request for the one-step timestamping packets of skb queue. This also
affects skb headroom allocation. Let's use skb->cb[0] to mark the
timestamping request for each skb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke dpaa2_eth_enable_tx_tstamp() once in code after building FD,
rather than calling it in dpaa2_eth_build_single_fd(),
dpaa2_eth_build_sg_fd_single_buf(), and dpaa2_eth_build_sg_fd().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a global ptp_qoriq structure pointer, and export to use.
The ptp clock operations will be used in dpaa2-eth driver.
For example, supporting one step timestamping needs to write
current time to hardware frame annotation before sending and
then hardware inserts the delay time on frame during sending.
So in driver, at least clock gettime operation will be needed
to make sure right time is written to hardware frame annotation
for one step timestamping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add APIs of 1588 single step timestamping.
- dpni_set_single_step_cfg
- dpni_get_single_step_cfg
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/freescale/fec_ptp.c:523:6: warning:
variable 'ns' set but not used [-Wunused-but-set-variable]
523 | u64 ns;
| ^~
After commit 6605b730c0 ("FEC: Add time stamping code and a PTP
hardware clock"), variable 'ns' is never used in fec_time_keep(),
so removing it to avoid build warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the correct resolution for the conflict from
merging the "net" tree fix:
commit 26cb7085c8 ("enetc: Remove the mdio bus on PF probe bailout")
with the "net-next" new work:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
that moved mdio bus allocation to an ealier stage of
the PF probing routine.
Fixes: a57066b1a0 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the error path for regulator disable.
Fixes: 9269e5560b ("net: fec: add phy-reset-gpios PROBE_DEFER check")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch warning:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:2419
alloc_channel() warn: passing zero to 'ERR_PTR'
setup_dpcon() should return ERR_PTR(err) instead of zero in error
handling case.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory allocation for ethernet address hash table.
The code was wrongly allocating an array for eth hash table which
is incorrect because this is the main structure for eth hash table
(struct eth_hash_t) that contains inside a number of elements.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a safe check to avoid dereferencing null pointer
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter 'priority' is incorrectly forced to zero which ultimately
induces logically dead code in the subsequent lines.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check before using returned value to avoid dereferencing null pointer.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Potentially overflowing expression (ts_freq << 16 and intgr << 16)
declared as type u32 (32-bit unsigned) is evaluated using 32-bit
arithmetic and then used in a context that expects an expression of
type u64 (64-bit unsigned) which ultimately is used as 16-bit
unsigned by typecasting to u16. Fixed by using an unsigned 32-bit
integer since the value is truncated anyway in the end.
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of invalid rule, a positive value EINVAL is returned here.
I think this is a typo error. It is necessary to return an error value.
Cc: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
