Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCYxNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl4pQCfaQBjMxPpp6TVcHANZ/O+zE3NH/wAoL11p3IB
KUq8v9pmcHO8sW5TWOJw
=iYGf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (142 commits)
USB: serial: option: add Fibocom NL678 series
cdc-acm: fix abnormal DATA RX issue for Mediatek Preloader.
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()
usb: typec: tcpm: Extend the matching rules on PPS APDO selection
usb: typec: Improve Alt Mode documentation
usb: musb: dsps: fix runtime pm for peripheral mode
usb: musb: dsps: fix otg state machine
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
usb: renesas_usbhs: add support for RZ/G2E
usb: ehci-omap: Fix deferred probe for phy handling
usb: roles: Add a description for the class to Kconfig
usb: renesas_usbhs: mark PM functions as __maybe_unused
usb: core: Remove unnecessary memset()
usb: host: isp1362-hcd: convert to DEFINE_SHOW_ATTRIBUTE
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
...
This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting to
get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4, mlx5,
qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use write()
for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into
a big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and sysfs
files
- First steps toward removing 'uobject' from the view of the drivers
-----BEGIN PGP SIGNATURE-----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=T0p1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting
to get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4,
mlx5, qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use
write() for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into a
big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page
tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and
sysfs files
- First steps toward removing 'uobject' from the view of the drivers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (193 commits)
RDMA/srpt: Use kmem_cache_free() instead of kfree()
RDMA/mlx5: Signedness bug in UVERBS_HANDLER()
IB/uverbs: Signedness bug in UVERBS_HANDLER()
IB/mlx5: Allocate the per-port Q counter shared when DEVX is supported
IB/umad: Start using dev_groups of class
IB/umad: Use class_groups and let core create class file
IB/umad: Refactor code to use cdev_device_add()
IB/umad: Avoid destroying device while it is accessed
IB/umad: Simplify and avoid dynamic allocation of class
IB/mlx5: Fix wrong error unwind
IB/mlx4: Remove set but not used variable 'pd'
RDMA/iwcm: Don't copy past the end of dev_name() string
IB/mlx5: Fix long EEH recover time with NVMe offloads
IB/mlx5: Simplify netdev unbinding
IB/core: Move query port to ioctl
RDMA/nldev: Expose port_cap_flags2
IB/core: uverbs copy to struct or zero helper
IB/rxe: Reuse code which sets port state
IB/rxe: Make counters thread safe
IB/mlx5: Use the correct commands for UMEM and UCTX allocation
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Pull RCU updates from Ingo Molnar:
"The biggest RCU changes in this cycle were:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions to
their vanilla RCU counterparts. This series is a step towards
complete removal of the RCU-bh and RCU-sched update-side functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for rcutorture
testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein for a
bag-on-head-class bug.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
rcutorture: Don't do busted forward-progress testing
rcutorture: Use 100ms buckets for forward-progress callback histograms
rcutorture: Recover from OOM during forward-progress tests
rcutorture: Print forward-progress test age upon failure
rcutorture: Print time since GP end upon forward-progress failure
rcutorture: Print histogram of CB invocation at OOM time
rcutorture: Print GP age upon forward-progress failure
rcu: Print per-CPU callback counts for forward-progress failures
rcu: Account for nocb-CPU callback counts in RCU CPU stall warnings
rcutorture: Dump grace-period diagnostics upon forward-progress OOM
rcutorture: Prepare for asynchronous access to rcu_fwd_startat
torture: Remove unnecessary "ret" variables
rcutorture: Affinity forward-progress test to avoid housekeeping CPUs
rcutorture: Break up too-long rcu_torture_fwd_prog() function
rcutorture: Remove cbflood facility
torture: Bring any extra CPUs online during kernel startup
rcutorture: Add call_rcu() flooding forward-progress tests
rcutorture/formal: Replace synchronize_sched() with synchronize_rcu()
tools/kernel.h: Replace synchronize_sched() with synchronize_rcu()
net/decnet: Replace rcu_barrier_bh() with rcu_barrier()
...
The two different assignments for pkt_len are actually the same and
so the if statement is redundant and can be removed. Masking a u8
return value from inb() with 0xFF is also redundant and can also be
emoved.
Similarly, the two different outb calls are identical as the mask
of 0xff on the second outb is redundant since a u8 is being written,
so the if statement is also redundant and can be also removed.
Detected by CoverityScan, CID#1475639 ("Identical code for different
branches")
V2: Remove the if statement for the outb calls, thanks to David
Miller for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This happened when I tried to boot normal Fedora 29 system with latest
available kernel (from fedora rawhide, plus some unrelated custom
patches):
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0010 [#1] SMP PTI
CPU: 6 PID: 1422 Comm: libvirtd Tainted: G I 4.20.0-0.rc7.git3.hpsa2.1.fc29.x86_64 #1
Hardware name: HP ProLiant BL460c G6, BIOS I24 05/21/2018
RIP: 0010: (null)
Code: Bad RIP value.
RSP: 0018:ffffa47ccdc9fbe0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00000000000003e8 RCX: ffffa47ccdc9fbf8
RDX: ffffa47ccdc9fc00 RSI: ffff97d9ee7b01f8 RDI: ffff97d9f0150b80
RBP: ffff97d9f0150b80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000003
R13: ffff97d9ef1e53e8 R14: 0000000000000009 R15: ffff97d9f0ac6730
FS: 00007f4d224ef700(0000) GS:ffff97d9fa200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 00000011ece52006 CR4: 00000000000206e0
Call Trace:
? bnx2x_chip_cleanup+0x195/0x610 [bnx2x]
? bnx2x_nic_unload+0x1e2/0x8f0 [bnx2x]
? bnx2x_reload_if_running+0x24/0x40 [bnx2x]
? bnx2x_set_features+0x79/0xa0 [bnx2x]
? __netdev_update_features+0x244/0x9e0
? netlink_broadcast_filtered+0x136/0x4b0
? netdev_update_features+0x22/0x60
? dev_disable_lro+0x1c/0xe0
? devinet_sysctl_forward+0x1c6/0x211
? proc_sys_call_handler+0xab/0x100
? __vfs_write+0x36/0x1a0
? rcu_read_lock_sched_held+0x79/0x80
? rcu_sync_lockdep_assert+0x2e/0x60
? __sb_start_write+0x14c/0x1b0
? vfs_write+0x159/0x1c0
? vfs_write+0xba/0x1c0
? ksys_write+0x52/0xc0
? do_syscall_64+0x60/0x1f0
? entry_SYSCALL_64_after_hwframe+0x49/0xbe
After some investigation I figured out that recently added cleanup code
tries to call VLAN filtering de-initialization function which exist only
for newer hardware. Corresponding function pointer is not
set (== 0) for older hardware, namely these chips:
#define CHIP_NUM_57710 0x164e
#define CHIP_NUM_57711 0x164f
#define CHIP_NUM_57711E 0x1650
And I have one of those in my test system:
Broadcom Inc. and subsidiaries NetXtreme II BCM57711E 10-Gigabit PCIe [14e4:1650]
Function bnx2x_init_vlan_mac_fp_objs() from
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h decides whether to
initialize relevant pointers in bnx2x_sp_objs.vlan_obj or not.
This regression was introduced after v4.20-rc7, and still exists in v4.20
release.
Fixes: 04f05230c5 ("bnx2x: Remove configured vlans as part of unload sequence.")
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop LIST_HEAD where the variable it declares has never
been used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: c82e9aa0a8 ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop LIST_HEAD where the variable it declares is never used.
The uses were removed in 244cd96adb ("net_sched: remove
list_head from tc_action"), but not the declaration.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: 244cd96adb ("net_sched: remove list_head from tc_action")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop LIST_HEAD where the variable it declares is never used.
These became useless in 244cd96adb ("net_sched: remove list_head
from tc_action")
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: 244cd96adb ("net_sched: remove list_head from tc_action")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes qmap header retrieval when modem is configured for
dl data aggregation.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Fibocom NL678 series cellular module QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x40 series chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netxen_rom_fast_read() fails, "bios" is left uninitialized and may
contain random value, thus should not be used.
The fix ensures that if netxen_rom_fast_read() fails, we return "-EIO".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool private flag 'xdp_tx_mpwqe' to control the feature
from userspace.
Feature is set ON by default, if supported.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for the HW feature of multi-packet WQE in XDP
xmit flow.
The conventional TX descriptor (WQE, Work Queue Element) serves
a single packet. Our HW has support for multi-packet WQE (MPWQE)
in which a single descriptor serves multiple TX packets.
This reduces both the PCI overhead and the CPU cycles wasted on
writing them.
In this patch we add support for the HW feature, which is supported
starting from ConnectX-5.
Performance:
Tested packet rate for UDP 64Byte multi-stream over ConnectX-5 NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
XDP_TX:
We see a huge gain on single port ConnectX-5, and reach the 100 Mpps
milestone.
* Single-port HCA:
Before: 70 Mpps
After: 100 Mpps (+42.8%)
* Dual-port HCA:
Before: 51.7 Mpps
After: 57.3 Mpps (+10.8%)
* In both cases we tested traffic on one port and for now On Dual-port HCAs
we see only small gain, we are working to overcome this bottleneck, but
for the moment only with experimental firmware on dual port HCAs we can
reach the wanted numbers as seen on Single-port HCAs.
XDP_REDIRECT:
Redirect from (A) ConnectX-5 to (B) ConnectX-5.
Due to a setup limitation, (A) and (B) are on different NUMA nodes,
so absolute performance numbers are not optimal.
Note:
Below is the transmit rate of (B), not the redirect rate of (A)
which is in some cases higher.
* (B) is single-port:
Before: 77 Mpps
After: 90 Mpps (+16.8%)
* (B) is dual-port:
Before: 61 Mpps
After: 72 Mpps (+18%)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Each xdp_wqe_info instance describes the number of data-segments
and WQEBBs of the WQE.
This is useful for a downstream patch that adds support for
Multi-Packet TX WQE feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This provides infrastructure to have multiple xdp_info instances
for the same consumer index.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of calculating the control segment to be used upon an
XDP xmit doorbell, save it in SQ structure.
Nullify when no pending doorbell.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Do not ignore the CQE opcode.
This helps expose issues and debug them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Do not maintain an SQ state bit to indicate whether an
XDP SQ serves redirect operations.
Instead, rely on the fact that such an XDP SQ doesn't reside
in an RQ instance, while the others do.
This info is not known to the XDP SQ functions themselves,
and they rely on their callers to distinguish between the cases.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
At the end of the RQ polling loop, some XDP-related operations
might be required. Before checking them one by one, check if
an XDP program is even loaded.
Combine all the checks and operations in a single function in xdp files.
This saves unnecessary checks for non-XDP flows.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The opcode indicates about the error reason.
Printing it helps in debug.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Virtio-net devices negotiate LRO support with the host.
Display the initially negotiated state with ethtool -k.
Also allow configuring it with ethtool -K, reusing the existing
virtnet_set_guest_offloads helper that configures LRO for XDP.
This is conditional on VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.
Virtio-net negotiates TSO4 and TSO6 separately, but ethtool does not
distinguish between the two. Display LRO as on only if any offload
is active.
RTNL is held while calling virtnet_set_features, same as on the path
from virtnet_xdp_set.
Changes v1 -> v2
- allow ethtool config (-K) only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
- show LRO as enabled if any LRO variant is enabled
- do not allow configuration while XDP is active
- differentiate current features from the capable set, to restore
on XDP down only those features that were active on XDP up
- move test out of VIRTIO_NET_F_CSUM/TSO branch, which is tx only
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-21
The following pull-request contains BPF updates for your *net-next* tree.
There is a merge conflict in test_verifier.c. Result looks as follows:
[...]
},
{
"calls: cross frame pruning",
.insns = {
[...]
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "function calls to other bpf functions are allowed for root only",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
{
"jset: functional",
.insns = {
[...]
{
"jset: unknown const compare not taken",
.insns = {
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0,
BPF_FUNC_get_prandom_u32),
BPF_JMP_IMM(BPF_JSET, BPF_REG_0, 1, 1),
BPF_LDX_MEM(BPF_B, BPF_REG_8, BPF_REG_9, 0),
BPF_EXIT_INSN(),
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "!read_ok",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
[...]
{
"jset: range",
.insns = {
[...]
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.result_unpriv = ACCEPT,
.result = ACCEPT,
},
The main changes are:
1) Various BTF related improvements in order to get line info
working. Meaning, verifier will now annotate the corresponding
BPF C code to the error log, from Martin and Yonghong.
2) Implement support for raw BPF tracepoints in modules, from Matt.
3) Add several improvements to verifier state logic, namely speeding
up stacksafe check, optimizations for stack state equivalence
test and safety checks for liveness analysis, from Alexei.
4) Teach verifier to make use of BPF_JSET instruction, add several
test cases to kselftests and remove nfp specific JSET optimization
now that verifier has awareness, from Jakub.
5) Improve BPF verifier's slot_type marking logic in order to
allow more stack slot sharing, from Jiong.
6) Add sk_msg->size member for context access and add set of fixes
and improvements to make sock_map with kTLS usable with openssl
based applications, from John.
7) Several cleanups and documentation updates in bpftool as well as
auto-mount of tracefs for "bpftool prog tracelog" command,
from Quentin.
8) Include sub-program tags from now on in bpf_prog_info in order to
have a reliable way for user space to get all tags of the program
e.g. needed for kallsyms correlation, from Song.
9) Add BTF annotations for cgroup_local_storage BPF maps and
implement bpf fs pretty print support, from Roman.
10) Fix bpftool in order to allow for cross-compilation, from Ivan.
11) Update of bpftool license to GPLv2-only + BSD-2-Clause in order
to be compatible with libbfd and allow for Debian packaging,
from Jakub.
12) Remove an obsolete prog->aux sanitation in dump and get rid of
version check for prog load, from Daniel.
13) Fix a memory leak in libbpf's line info handling, from Prashant.
14) Fix cpumap's frame alignment for build_skb() so that skb_shared_info
does not get unaligned, from Jesper.
15) Fix test_progs kselftest to work with older compilers which are less
smart in optimizing (and thus throwing build error), from Stanislav.
16) Cleanup and simplify AF_XDP socket teardown, from Björn.
17) Fix sk lookup in BPF kselftest's test_sock_addr with regards
to netns_id argument, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract "Protocol" field decompression code from transport protocols to
PPP generic layer, where it actually belongs. As a consequence, this
patch fixes incorrect place of PFC decompression in L2TP driver (when
it's not PPPOX_BOUND) and also enables this decompression for other
protocols, like PPPoE.
Protocol field decompression also happens in PPP Multilink Protocol
code and in PPP compression protocols implementations (bsd, deflate,
mppe). It looks like there is no easy way to get rid of that, so it was
decided to leave it as is, but provide those cases with appropriate
comments instead.
Changes in v2:
- Fix the order of checking skb data room and proto decompression
- Remove "inline" keyword from ppp_decompress_proto()
- Don't split line before function name
- Prefix ppp_decompress_proto() function with "__"
- Add ppp_decompress_proto() function with skb data room checks
- Add description for introduced functions
- Fix comments (as per review on mailing list)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing indirect access in the Ocelot chip, a command is setup,
issued and then we need to poll until the result is ready. The polling
timeout is specified in milliseconds in the datasheet and not in
register access attempts.
It is not a bug on the currently supported platform, but we observed
that the code does not work properly on other platforms that we want to
support as the timing requirements there are different.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC table in Ocelot supports auto aging (normal) and static entries.
MAC entries that is manually configured should be static and not subject
to aging.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Allan Nielsen <allan.nielsen@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports. In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60. Port 6 is the host port.
Setting a zero value can be used to stop port from receiving.
However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate. This does not apply to
multicast and broadcast addresses though. To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.
Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving the conflict wrt. the vxlan_fdb_update call
in vxlan_changelink() I made the last argument false instead
of true.
Fix this.
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds some misc updates and the support for tunnels over VLAN
tc offloads.
From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock
From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128
From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.
Patch 4 avoids crash for TC flow with egress upper devices
Patch 5 refactors tunnel routing devs into a helper function
Patch 6 avoids crash for TC encap flows with vlan on underlay
Patches 7-8 refactor encap tunnel header preparing code.
Patch 9 adds support for building VLAN tagged ETH header.
Patch 10 adds support for tunnel routing to VLAN device.
From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcG5O8AAoJEEg/ir3gV/o+v0AH/ja1bJ6PkAlw2bCRMIuI6HK/
1vh9n8D74tIOAlvUi6QiLOgJ7CLdAgiAVFppDWzJSBUsY2XNAtRdYvLDDt9hGafO
QGysBWNVcX2aUVp+pLDCCVEYBWyyIzW416CWHx2IUgdAg9S6cvJK6P/81wd+l4Zp
8YlPstEUANP/JKZxHHjSelMcnY+Bj0JrDzuyyyaQdwmcHo5I7Ht0tNex14yFfFbl
gd7YvfPr1PtovPX2w9hMt3y3ml4mommB+jtxc0+59D+A7680hBOpAnH5pONms9rv
OKKKV8KqpxL1m32/TGbd7XSG+llLJwsSM6RtD4oUdiPA4iCiVDVdreP5vac52C4=
=0QQ5
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-12-19
This series adds some misc updates and the support for tunnels over VLAN
tc offloads.
From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock
From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128
From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.
Patch 4 avoids crash for TC flow with egress upper devices
Patch 5 refactors tunnel routing devs into a helper function
Patch 6 avoids crash for TC encap flows with vlan on underlay
Patches 7-8 refactor encap tunnel header preparing code.
Patch 9 adds support for building VLAN tagged ETH header.
Patch 10 adds support for tunnel routing to VLAN device.
From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
VID 1 is not reserved anymore, so remove the check that prevented the
creation of VLAN devices with this VID over mlxsw ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.
The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.
Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.
The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function allows flushing all the existing VLAN entries on a port. It
is invoked when a port is destroyed and when it is unlinked from a LAG.
In the latter case, when moving to the new default VLAN, there will not
be a need to destroy the default VLAN entry.
Therefore, add an argument that allows to control whether the default
port VLAN should be destroyed or not. Currently it is always set to
'true'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver does not set the port's PVID when initializing a
new port. This is because the driver is using VID 1 as PVID which is the
firmware default.
Subsequent patches are going to change the PVID the driver is setting
when initializing a new port.
Prepare for that by explicitly setting the port's PVID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).
Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.
In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.
The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.
Instead, call into the bridge code which will check if NVE should be
enabled on the FID.
This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-12-20
This series contains updates to e100, igb, ixgbe, i40e and ice drivers.
I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics. This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.
Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.
Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.
YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.
Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.
Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.
Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.
Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in. This was due to the
driver not setting PME during runtime suspend.
Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
Use the mii_bus callbacks to address the entire clause 22/45 address
space. Enables userspace to poke switch registers instead of a single
PHY address.
The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock. This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.
While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit 42eca23021 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes: 42eca23021 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.
See commit 13a8cd191a ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
