Convert the topology manager to use struct drm_edid, add
drm_dp_mst_edid_read() that returns drm_edid, and rewrite the old
drm_dp_mst_get_edid() to use it.
Note that the old drm_get_edid() ended up calling
drm_connector_update_edid_property(). This responsibility is now
deferred to drivers, which all do it anyway after calling
drm_dp_mst_edid_read() or drm_dp_mst_get_edid().
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c32e5c241934093fc4144eed4c01155e1f03af1.1685437501.git.jani.nikula@intel.com
DSC model contains pre-SCR RC parameters for other bpp/bpc combinations,
include them here for completeness. The values were generated from the
'pre_scr_cfg_files_for_reference' files found in DSC models 20210623.
The same fileset is a part of DSC model 20161212.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-8-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
The array of rc_parameters contains a mixture of parameters from DSC 1.1
and DSC 1.2 standards. Split these tow configuration arrays in
preparation to adding more configuration data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Suraj Kandpal
Reviewed-by: Suraj Kandpal
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-7-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
Next commits are going to add support for additional RC parameter lookup
tables. These tables are going to use different bpp/bpc combinations,
thus it makes little sense to keep the 2d array for RC parameters.
Switch to using the flat array.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-6-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
Move DSC RC tables to DRM DSC helper. No additional code changes
and/or cleanups are a part of this commit, it will be cleaned up in the
followup commits.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-4-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
The rc_buf_thresh values are common to all DSC implementations. Move
them to the common helper together with the code to propagate them to
the drm_dsc_config.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517102807.2181589-3-dmitry.baryshkov@linaro.org
Acked-by: Dave Airlie <airlied@redhat.com>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EDID of an HDR display defines EOTFs that are supported
by the display and can be set in the HDR metadata infoframe.
Userspace is expected to read the EDID and set an appropriate
HDR_OUTPUT_METADATA.
In drm_parse_hdr_metadata_block the kernel reads the supported
EOTFs from the EDID and stores them in the
drm_connector->hdr_sink_metadata. While doing so it also
filters the EOTFs to the EOTFs the kernel knows about.
When an HDR_OUTPUT_METADATA is set it then checks to
make sure the EOTF is a supported EOTF. In cases where
the kernel doesn't know about a new EOTF this check will
fail, even if the EDID advertises support.
Since it is expected that userspace reads the EDID to understand
what the display supports it doesn't make sense for DRM to block
an HDR_OUTPUT_METADATA if it contains an EOTF the kernel doesn't
understand.
This comes with the added benefit of future-proofing metadata
support. If the spec defines a new EOTF there is no need to
update DRM and an compositor can immediately make use of it.
Bug: https://gitlab.freedesktop.org/wayland/weston/-/issues/609
v2: Distinguish EOTFs defind in kernel and ones defined
in EDID in the commit description (Pekka)
v3: Rebase; drm_hdmi_infoframe_set_hdr_metadata moved
to drm_hdmi_helper.c
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Sebastian Wick <sebastian.wick@redhat.com>
Cc: Vitaly.Prosyak@amd.com
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-By: Joshua Ashton <joshua@froggi.es>
Link: https://patchwork.freedesktop.org/patch/msgid/20230113162428.33874-2-harry.wentland@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The EDID of an HDR display defines EOTFs that are supported
by the display and can be set in the HDR metadata infoframe.
Userspace is expected to read the EDID and set an appropriate
HDR_OUTPUT_METADATA.
In drm_parse_hdr_metadata_block the kernel reads the supported
EOTFs from the EDID and stores them in the
drm_connector->hdr_sink_metadata. While doing so it also
filters the EOTFs to the EOTFs the kernel knows about.
When an HDR_OUTPUT_METADATA is set it then checks to
make sure the EOTF is a supported EOTF. In cases where
the kernel doesn't know about a new EOTF this check will
fail, even if the EDID advertises support.
Since it is expected that userspace reads the EDID to understand
what the display supports it doesn't make sense for DRM to block
an HDR_OUTPUT_METADATA if it contains an EOTF the kernel doesn't
understand.
This comes with the added benefit of future-proofing metadata
support. If the spec defines a new EOTF there is no need to
update DRM and an compositor can immediately make use of it.
Bug: https://gitlab.freedesktop.org/wayland/weston/-/issues/609
v2: Distinguish EOTFs defind in kernel and ones defined
in EDID in the commit description (Pekka)
v3: Rebase; drm_hdmi_infoframe_set_hdr_metadata moved
to drm_hdmi_helper.c
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Sebastian Wick <sebastian.wick@redhat.com>
Cc: Vitaly.Prosyak@amd.com
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-By: Joshua Ashton <joshua@froggi.es>
Link: https://patchwork.freedesktop.org/patch/msgid/20230113162428.33874-2-harry.wentland@amd.com
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Add a function to get the old MST topology state, required by a
follow-up i915 patch.
While at it clarify the code comment of
drm_atomic_get_new_mst_topology_state() and add _new prefix
to the new state pointer to remind about its difference from the old
state.
v2: Use old_/new_ prefixes for the state pointers. (Ville)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org # 6.1
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-3-imre.deak@intel.com
Atm, drm_dp_remove_payload() uses the same payload state to both get the
vc_start_slot required for the payload removal DPCD message and to
deduct time_slots from vc_start_slot of all payloads after the one being
removed.
The above isn't always correct, as vc_start_slot must be the up-to-date
version contained in the new payload state, but time_slots must be the
one used when the payload was previously added, contained in the old
payload state. The new payload's time_slots can change vs. the old one
if the current atomic commit changes the corresponding mode.
This patch let's drivers pass the old and new payload states to
drm_dp_remove_payload(), but keeps these the same for now in all drivers
not to change the behavior. A follow-up i915 patch will pass in that
driver the correct old and new states to the function.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org # 6.1
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-2-imre.deak@intel.com
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_uevent_modalias() does not modify the device pointer passed to
it, so mark it constant. In order to properly do this, a number of
busses need to have a modalias function added as they were attempting to
just point to of_device_uevent_modalias instead of their bus-specific
modalias function. This is fine except if the prototype for a bus and
device type modalias function diverges and then problems could happen. To
prevent all of that, just wrap the call to of_device_uevent_modalias()
directly for each bus and device type individually.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Liang He <windhl@126.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Cc: Zou Wei <zou_wei@huawei.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@lists.linux.dev
Cc: dri-devel@lists.freedesktop.org
Cc: devicetree@vger.kernel.org
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[why & how]
We still need to refer to port while removing payload at commit_tail.
we should keep the kref till then to release.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2171
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 4d07b0bc40 ("drm/display/dp_mst: Move all payload info into the atomic state")
Cc: stable@vger.kernel.org # 6.1
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Tested-by: Didier Raboud <odyx@debian.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If an MST stream is enabled on a disconnected sink, the payload for the
stream is not created and the MST manager's payload count/next start VC
slot is not updated. Since the payload's start VC slot may still contain
a valid value (!= -1) the subsequent disabling of such a stream could
cause an incorrect decrease of the payload count/next start VC slot in
drm_dp_remove_payload() and hence later payload additions will fail.
Fix the above by marking the payload as invalid in the above case, so
that it's skipped during payload removal. While at it add a debug print
for this case.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v6.1+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214184258.2869417-3-imre.deak@intel.com
After an error during receiving a packet for a multi-packet DP MST
sideband message, the state tracking which packets have been received
already is not reset. This prevents the reception of subsequent down
messages (due to the pending message not yet completed with an
end-of-message-transfer packet).
Fix the above by resetting the reception state after a packet error.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214184258.2869417-2-imre.deak@intel.com
If the sink gets disconnected during receiving a multi-packet DP MST AUX
down-reply/up-request sideband message, the state keeping track of which
packets have been received already is not reset. This results in a failed
sanity check for the subsequent message packet received after a sink is
reconnected (due to the pending message not yet completed with an
end-of-message-transfer packet), indicated by the
"sideband msg set header failed"
error.
Fix the above by resetting the up/down message reception state after a
disconnect event.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221214184258.2869417-1-imre.deak@intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmN6wAgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0EYH/3/RO90NbrFItraN
Lzr+d3VdbGjTu8xd1M+PRTmwh3zxLpB+Jwqr0T0A2gzL9B/D+AUPUJdrCVbv9DqS
FLJAVqoeV20dNBAHSffOOLPsgCZ+Eu+LzlNN7Iqde0e8cyZICFMNktitui84Xm/i
1NgFVgz9OZ6+aieYvUj3FrFq0p8GTIaC/oybDZrxYKcO8ZzKVMJ11swRw10wwq0g
qOOECvV3w7wlQ8upQZkzFxItKFc7EexZI6R4elXeGSJJ9Hlc092dv/zsKB9dwV+k
WcwkJrZRoezYXzgGBFxUcQtzi+ethjrPjuJuM1rYLUSIcfIW/0lkaSLgRoBu8D+I
1GfXkXs=
=gt6P
-----END PGP SIGNATURE-----
Backmerge tag 'v6.1-rc6' into drm-next
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like that we're accidentally dropping a pretty important return code
here. For some reason, we just return -EINVAL if we fail to get the MST
topology state. This is wrong: error codes are important and should never
be squashed without being handled, which here seems to have the potential
to cause a deadlock.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Fixes: 8ec046716c ("drm/dp_mst: Add helper to trigger modeset on affected DSC MST CRTCs")
Cc: <stable@vger.kernel.org> # v5.6+
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current dual mode adaptor ("DP++") detection code assumes that all
adaptors support i2c sub-addressing for read operations from the
DP-HDMI adaptor ID buffer. It has been observed that multiple
adaptors do not in fact support this, and always return data starting
at register 0. On affected adaptors, the code fails to read the proper
registers that would identify the device as a type 2 adaptor, and
handles those as type 1, limiting the TMDS clock to 165MHz, even if
the according register would announce a higher TMDS clock.
Fix this by always reading the ID buffer starting from offset 0, and
discarding any bytes before the actual offset of interest.
We tried finding authoritative documentation on whether or not this is
allowed behaviour, but since all the official VESA docs are paywalled,
the best we could come up with was the spec sheet for Texas Instruments'
SNx5DP149 chip family.[1] It explicitly mentions that sub-addressing is
supported for register writes, but *not* for reads (See NOTE in
section 8.5.3). Unless TI openly decided to violate the VESA spec, one
could take that as a hint that sub-addressing is in fact not mandated
by VESA.
The other two adaptors affected used the PS8409(A) and the LT8611,
according to the data returned from their ID buffers.
[1] https://www.ti.com/lit/ds/symlink/sn75dp149.pdf
Cc: stable@vger.kernel.org
Signed-off-by: Simon Rettberg <simon.rettberg@rz.uni-freiburg.de>
Reviewed-by: Rafael Gieschke <rafael.gieschke@rz.uni-freiburg.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006113314.41101987@computer
Acked-by: Jani Nikula <jani.nikula@intel.com>
While it takes more vertical space, sorted build lists with one object
per line are arguably easier to manage, especially when there are
conflicting changes.
Split anything with more than one object file.
v2: also split drm_cache.o and put it after drm_bridge.o (Andi)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221011140830.3257655-1-jani.nikula@intel.com
Here is the big set of driver core and debug printk changes for 6.1-rc1.
Included in here is:
- dynamic debug updates for the core and the drm subsystem. The
drm changes have all been acked by the relevant maintainers.
- kernfs fixes for syzbot reported problems
- kernfs refactors and updates for cgroup requirements
- magic number cleanups and removals from the kernel tree (they
were not being used and they really did not actually do
anything.)
- other tiny cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BYUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylozwCdFRlcghaf7XBUyNgRZRwMC+oQI8EAn1G/nEDE
6aFd2er41uK0IGQnSmYO
=OK0k
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core and debug printk changes for
6.1-rc1. Included in here is:
- dynamic debug updates for the core and the drm subsystem. The drm
changes have all been acked by the relevant maintainers
- kernfs fixes for syzbot reported problems
- kernfs refactors and updates for cgroup requirements
- magic number cleanups and removals from the kernel tree (they were
not being used and they really did not actually do anything)
- other tiny cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (74 commits)
docs: filesystems: sysfs: Make text and code for ->show() consistent
Documentation: NBD_REQUEST_MAGIC isn't a magic number
a.out: restore CMAGIC
device property: Add const qualifier to device_get_match_data() parameter
drm_print: add _ddebug descriptor to drm_*dbg prototypes
drm_print: prefer bare printk KERN_DEBUG on generic fn
drm_print: optimize drm_debug_enabled for jump-label
drm-print: add drm_dbg_driver to improve namespace symmetry
drm-print.h: include dyndbg header
drm_print: wrap drm_*_dbg in dyndbg descriptor factory macro
drm_print: interpose drm_*dbg with forwarding macros
drm: POC drm on dyndbg - use in core, 2 helpers, 3 drivers.
drm_print: condense enum drm_debug_category
debugfs: use DEFINE_SHOW_ATTRIBUTE to define debugfs_regset32_fops
driver core: use IS_ERR_OR_NULL() helper in device_create_groups_vargs()
Documentation: ENI155_MAGIC isn't a magic number
Documentation: NBD_REPLY_MAGIC isn't a magic number
nbd: remove define-only NBD_MAGIC, previously magic number
Documentation: FW_HEADER_MAGIC isn't a magic number
Documentation: EEPROM_MAGIC_VALUE isn't a magic number
...
The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)
The problem is with DP PHY compliance setup as follow:
[DPTX + on board LTTPR]------Main Link--->[Scope]
^ |
| |
| |
----------Aux Ch------>[Aux Emulator]
At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.
The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow
igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2
OR
printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc
seek=$((0x100))
This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.
As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."
In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.
The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET
[1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance
[2]: Configuring UnigrafDPTC Controller - Automation Test Sequence
https://www.keysight.com/us/en/assets/9922-01244/help-files/
D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Or Cochvi <or.cochvi@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com
Use DECLARE_DYNDBG_CLASSMAP across DRM:
- in .c files, since macro defines/initializes a record
- in drivers, $mod_{drv,drm,param}.c
ie where param setup is done, since a classmap is param related
- in drm/drm_print.c
since existing __drm_debug param is defined there,
and we ifdef it, and provide an elaborated alternative.
- in drm_*_helper modules:
dp/drm_dp - 1st item in makefile target
drivers/gpu/drm/drm_crtc_helper.c - random pick iirc.
Since these modules all use identical CLASSMAP declarations (ie: names
and .class_id's) they will all respond together to "class DRM_UT_*"
query-commands:
:#> echo class DRM_UT_KMS +p > /proc/dynamic_debug/control
NOTES:
This changes __drm_debug from int to ulong, so BIT() is usable on it.
DRM's enum drm_debug_category values need to sync with the index of
their respective class-names here. Then .class_id == category, and
dyndbg's class FOO mechanisms will enable drm_dbg(DRM_UT_KMS, ...).
Though DRM needs consistent categories across all modules, thats not
generally needed; modules X and Y could define FOO differently (ie a
different NAME => class_id mapping), changes are made according to
each module's private class-map.
No callsites are actually selected by this patch, since none are
class'd yet.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-3-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's some interactions between the SCDC setup and the disconnection /
reconnection of displays. Let's document it and a solution.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-9-maxime@cerno.tech
Add a helper for getting the DP PHY name. In the interest of caller
simplicity and to avoid allocations and passing in of buffers, duplicate
the const strings to return. It's a minor penalty to pay for simplicity
in all the call sites.
v2: Rebase, add kernel-doc, ensure non-NULL always
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b08dc12a7e621a48ec35546d6cd1ed4b1434810d.1660553850.git.jani.nikula@intel.com
Now that we've finally gotten rid of the non-atomic MST users leftover in
the kernel, we can finally get rid of all of the legacy payload code we
have and move as much as possible into the MST atomic state structs. The
main purpose of this is to make the MST code a lot less confusing to work
on, as there's a lot of duplicated logic that doesn't really need to be
here. As well, this should make introducing features like fallback link
retraining and DSC support far easier.
Since the old payload code was pretty gnarly and there's a Lot of changes
here, I expect this might be a bit difficult to review. So to make things
as easy as possible for reviewers, I'll sum up how both the old and new
code worked here (it took me a while to figure this out too!).
The old MST code basically worked by maintaining two different payload
tables - proposed_vcpis, and payloads. proposed_vcpis would hold the
modified payload we wanted to push to the topology, while payloads held the
payload table that was currently programmed in hardware. Modifications to
proposed_vcpis would be handled through drm_dp_allocate_vcpi(),
drm_dp_mst_deallocate_vcpi(), and drm_dp_mst_reset_vcpi_slots(). Then, they
would be pushed via drm_dp_mst_update_payload_step1() and
drm_dp_mst_update_payload_step2().
Furthermore, it's important to note how adding and removing VC payloads
actually worked with drm_dp_mst_update_payload_step1(). When a VC payload
is removed from the VC table, all VC payloads which come after the removed
VC payload's slots must have their time slots shifted towards the start of
the table. The old code handles this by looping through the entire payload
table and recomputing the start slot for every payload in the topology from
scratch. While very much overkill, this ends up doing the right thing
because we always order the VCPIs for payloads from first to last starting
timeslot.
It's important to also note that drm_dp_mst_update_payload_step2() isn't
actually limited to updating a single payload - the driver can use it to
queue up multiple payload changes so that as many of them can be sent as
possible before waiting for the ACT. This is -technically- not against
spec, but as Wayne Lin has pointed out it's not consistently implemented
correctly in hubs - so it might as well be.
drm_dp_mst_update_payload_step2() is pretty self explanatory and basically
the same between the old and new code, save for the fact we don't have a
second step for deleting payloads anymore -and thus rename it to
drm_dp_mst_add_payload_step2().
The new payload code stores all of the current payload info within the MST
atomic state and computes as much of the state as possible ahead of time.
This has the one exception of the starting timeslots for payloads, which
can't be determined at atomic check time since the starting time slots will
vary depending on what order CRTCs are enabled in the atomic state - which
varies from driver to driver. These are still stored in the atomic MST
state, but are only copied from the old MST state during atomic commit
time. Likewise, this is when new start slots are determined.
Adding/removing payloads now works much more closely to how things are
described in the spec. When we delete a payload, we loop through the
current list of payloads and update the start slots for any payloads whose
time slots came after the payload we just deleted. Determining the starting
time slots for new payloads being added is done by simply keeping track of
where the end of the VC table is in
drm_dp_mst_topology_mgr->next_start_slot. Additionally, it's worth noting
that we no longer have a single update_payload() function. Instead, we now
have drm_dp_mst_add_payload_step1|2() and drm_dp_mst_remove_payload(). As
such, it's now left it up to the driver to figure out when to add or remove
payloads. The driver already knows when it's disabling/enabling CRTCs, so
it also already knows when payloads should be added or removed.
Changes since v1:
* Refactor around all of the completely dead code changes that are
happening in amdgpu for some reason when they really shouldn't even be
there in the first place… :\
* Remove mention of sending one ACT per series of payload updates. As Wayne
Lin pointed out, there are apparently hubs on the market that don't work
correctly with this scheme and require a separate ACT per payload update.
* Fix accidental drop of mst_mgr.lock - Wayne Lin
* Remove mentions of allowing multiple ACT updates per payload change,
mention that this is a result of vendors not consistently supporting this
part of the spec and requiring a unique ACT for each payload change.
* Get rid of reference to drm_dp_mst_port in DC - turns out I just got
myself confused by DC and we don't actually need this.
Changes since v2:
* Get rid of fix for not sending payload deallocations if ddps=0 and just
go back to wayne's fix
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-18-lyude@redhat.com
Currently, we set drm_dp_atomic_payload->time_slots to 0 in order to
indicate that we're about to delete a payload in the current atomic state.
Since we're going to be dropping all of the legacy code for handling the
payload table however, we need to be able to ensure that we still keep
track of the current time slot allocations for each payload so we can reuse
this info when asking the root MST hub to delete payloads. We'll also be
using it to recalculate the start slots of each VC.
So, let's keep track of the intent of a payload in drm_dp_atomic_payload by
adding ->delete, which we set whenever we're planning on deleting a payload
during the current atomic commit.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-16-lyude@redhat.com
We want to start cutting down on all of the places that we use port
validation, so that ports may be removed from the topology as quickly as
possible to minimize the number of errors we run into as a result of being
out of sync with the current topology status. This isn't a very typical
scenario and I don't think I've ever even run into it - but since the next
commit is going to make some changes to payload updates depending on their
hotplug status I think it's a probably good idea to take precautions.
Let's do this with CSNs by moving some code around so that we only queue
link address probing work at the end of handling all CSNs - allowing us to
make sure we drop as many topology references as we can beforehand.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-15-lyude@redhat.com
There's another kind of situation where we could potentially race with
nonblocking modesets and MST, especially if we were to only use the locking
provided by atomic modesetting:
* Display 1 begins as enabled on DP-1 in SST mode
* Display 1 switches to MST mode, exposes one sink in MST mode
* Userspace does non-blocking modeset to disable the SST display
* Userspace does non-blocking modeset to enable the MST display with a
different CRTC, but the SST display hasn't been fully taken down yet
* Execution order between the last two commits isn't guaranteed since they
share no drm resources
We can fix this however, by ensuring that we always pull in the atomic
topology state whenever a connector capable of driving an MST display
performs its atomic check - and then tracking CRTC commits happening on the
SST connector in the MST topology state. So, let's add some simple helpers
for doing that and hook them up in various drivers.
v2:
* Use intel_dp_mst_source_support() to check for MST support in i915, fixes
CI failures
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-14-lyude@redhat.com
Currently with the MST helpers we avoid releasing payloads _and_ avoid
pulling in the MST state if there aren't any actual payload changes. While
we want to keep the first step, we need to now make sure that we're always
pulling in the MST state on all modesets that can modify payloads - even if
the resulting payloads in the atomic state are identical to the previous
ones.
This is mainly to make it so that if a CRTC is still assigned to a
connector but is set to DPMS off, the CRTC still holds it's payload
allocation in the atomic state and still appropriately pulls in the MST
state for commit tracking. Otherwise, we'll occasionally forget to update
MST payloads from changes caused by non-atomic DPMS changes. Doing this
also allows us to track bandwidth limitations in a state correctly even
between DPMS changes, so that there's no chance of a simple ->active change
being rejected by the atomic check.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-11-lyude@redhat.com
I'm not sure why, but at the time I originally wrote the find/release time
slot helpers I thought we should avoid keeping modeset tracking out of the
MST helpers. In retrospect though there's no actual good reason to do
this, and the logic has ended up being identical across all the drivers
using the helpers. Also, it needs to be fixed anyway so we don't break
things when going atomic-only with MST.
So, let's just move this code into drm_dp_atomic_release_time_slots() and
stop open coding it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-10-lyude@redhat.com
As Daniel Vetter pointed out, if we only use the atomic modesetting locks
with MST it's technically possible for a driver with non-blocking modesets
to race when it comes to MST displays - as we make the mistake of not doing
our own CRTC commit tracking in the topology_state object.
This could potentially cause problems if something like this happens:
* User starts non-blocking commit to disable CRTC-1 on MST topology 1
* User starts non-blocking commit to enable CRTC-2 on MST topology 1
There's no guarantee here that the commit for disabling CRTC-2 will only
occur after CRTC-1 has finished, since neither commit shares a CRTC - only
the private modesetting object for MST. Keep in mind this likely isn't a
problem for blocking modesets, only non-blocking.
So, begin fixing this by keeping track of which CRTCs on a topology have
changed by keeping track of which CRTCs we release or allocate timeslots
on. As well, add some helpers for:
* Setting up the drm_crtc_commit structs in the ->commit_setup hook
* Waiting for any CRTC dependencies from the previous topology state
v2:
* Use drm_dp_mst_atomic_setup_commit() directly - Jani
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-9-lyude@redhat.com
We already open-code this quite often, and will be iterating through
payloads even more once we've moved all of the payload tracking into the
atomic state. So, let's add a helper for doing this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-8-lyude@redhat.com
For some reason we mention returning 0 if "slots have been added back to
drm_dp_mst_topology_state->avail_slots". This is totally misleading,
avail_slots is simply for figuring out the total number of slots available
in total on the topology and has no relation to the current payload
allocations.
So, let's get rid of that comment.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-6-lyude@redhat.com
VCPI is only sort of the correct term here, originally the majority of this
code simply referred to timeslots vaguely as "slots" - and since I started
working on it and adding atomic functionality, the name "VCPI slots" has
been used to represent time slots.
Now that we actually have consistent access to the DisplayPort spec thanks
to VESA, I now know this isn't actually the proper term - as the
specification refers to these as time slots.
Since we're trying to make this code as easy to figure out as possible,
let's take this opportunity to correct this nomenclature and call them by
their proper name - timeslots. Likewise, we rename various functions
appropriately, along with replacing references in the kernel documentation
and various debugging messages.
It's important to note that this patch series leaves the legacy MST code
untouched for the most part, which is fine since we'll be removing it soon
anyhow. There should be no functional changes in this series.
v2:
* Add note that Wayne Lin from AMD suggested regarding slots being between
the source DP Tx and the immediate downstream DP Rx
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-5-lyude@redhat.com
In retrospect, the name I chose for this originally is confusing, as
there's a lot more info in here then just the VCPI. This really should be
called a payload. Let's make it more obvious that this is meant to be
related to the atomic state and is about payloads by renaming it to
drm_dp_mst_atomic_payload. Also, rename various variables throughout the
code that use atomic payloads.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-4-lyude@redhat.com
Currently, there is no way to identify if DSC pass-through can be
enabled and what aux DSC pass-through requests ought to be sent to. So,
add a variable to struct drm_dp_mst_port that keeps track of the
aforementioned information.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
