The busyd0 line transition can be very fast. The busy request may be
completed by busy_d0end, without waiting for the busy_d0 steps. Therefore,
clear the busyd0end irq flag, even if no busy_status.
Fixes: 0e68de6aa7 ("mmc: mmci: sdmmc: add busy_complete callback")
Cc: stable@vger.kernel.org
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200325143409.13005-2-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prepare the voltage switch procedure, the VSWITCHEN bit must be set
before sending the CMD11. To confirm completion of voltage switch, the
VSWEND flag must be checked.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-9-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware delay block is used to align the sampling clock on the data
received by SDMMC. It is mandatory for SDMMC to support the SDR104 mode.
The delay block is used to generate an output clock which is dephased from
the input clock. The phase of the output clock must be programmed by the
execute tuning interface.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-7-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sg_dma_xxx should be used after a dma_map_sg call has been done to get bus
addresses of each of the SG entries and their lengths. But mmci_host_ops
validate_data can be called before dma_map_sg. This patch replaces theses
macros by sg->offset and sg->length which are always defined.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-2-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make sdmmc_idma_validate_data to avoid the following warning
from sparse:
drivers/mmc/host/mmci_stm32_sdmmc.c:28:5: warning: symbol 'sdmmc_idma_validate_data' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines get_dctrl_cfg callback for sdmmc variant.
sdmmc variant has specific stm32 transfer modes.
sdmmc data transfer mode selection could be:
-Block data transfer ending on block count.
-SDIO multibyte data transfer.
-MMC Stream data transfer (not used).
-Block data transfer ending with STOP_TRANSMISSION command.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
