Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.
Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.
Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions
This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[ 614.050361] net eth0: DMA Tx error 0x174019
[ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[ 614.135428] 3 locks held by kworker/u4:4/40:
[ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[ 614.177528] #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[ 614.209033] #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[ 614.260854] Hardware name: ARM Test FPGA (DT)
[ 614.274734] Workqueue: rpciod rpc_async_schedule
[ 614.289022] Call trace:
[ 614.296871] dump_backtrace+0x0/0x1a0
[ 614.308311] show_stack+0x14/0x20
[ 614.318751] dump_stack+0xbc/0x100
[ 614.329403] ___might_sleep+0xf0/0x140
[ 614.341018] __might_sleep+0x4c/0x80
[ 614.352201] __mutex_lock+0x5c/0x8a8
[ 614.363348] mutex_lock_nested+0x1c/0x28
[ 614.375654] axienet_dma_err_handler+0x38/0x388
[ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8
[ 614.405894] tasklet_action+0x24/0x30
[ 614.417297] efi_header_end+0xe0/0x494
[ 614.429020] irq_exit+0xd0/0xd8
[ 614.439047] __handle_domain_irq+0x60/0xb0
[ 614.451877] gic_handle_irq+0xdc/0x2d0
[ 614.463486] el1_irq+0xcc/0x180
[ 614.473451] __tcp_transmit_skb+0x41c/0xb58
[ 614.486513] tcp_write_xmit+0x224/0x10a0
[ 614.498792] __tcp_push_pending_frames+0x38/0xc8
[ 614.513126] tcp_rcv_established+0x41c/0x820
[ 614.526301] tcp_v4_do_rcv+0x8c/0x218
[ 614.537784] __release_sock+0x5c/0x108
[ 614.549466] release_sock+0x34/0xa0
[ 614.560318] tcp_sendmsg+0x40/0x58
[ 614.571053] inet_sendmsg+0x40/0x68
[ 614.582061] sock_sendmsg+0x18/0x30
[ 614.593074] xs_sendpages+0x218/0x328
[ 614.604506] xs_tcp_send_request+0xa0/0x1b8
[ 614.617461] xprt_transmit+0xc8/0x4f0
[ 614.628943] call_transmit+0x8c/0xa0
[ 614.640028] __rpc_execute+0xbc/0x6f8
[ 614.651380] rpc_async_schedule+0x28/0x48
[ 614.663846] process_one_work+0x298/0x6a8
[ 614.676299] worker_thread+0x40/0x490
[ 614.687687] kthread+0x134/0x138
[ 614.697804] ret_from_fork+0x10/0x18
[ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to axienet, the temac driver is now architecture agnostic, and
can be at least compiled for several architectures.
Especially the fact that this is a soft IP for implementing in FPGAs
makes the current restriction rather pointless, as it could literally
appear on any architecture, as long as an FPGA is connected to the bus.
The driver hasn't been actually tried on any hardware, it is just a
drive-by patch when doing the same for axienet (a similar patch for
axienet is already merged).
This (temac and axienet) have been compile-tested for:
alpha hppa64 microblaze mips64 powerpc powerpc64 riscv64 s390 sparc64
(using kernel.org cross compilers).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use readl_poll_timeout() to replace the poll codes for simplify
iproc_mdio_wait_for_idle() function
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.
When merging with wireless-drivers this pull request has a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve that just drop the changes from commit cf52c8a776 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a38 (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.
Major changes:
qtnfmac
* support WPA3 SAE and OWE in AP mode
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
mt76
* MT7663 support for the MT7615 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeechaAAoJEG4XJFUm622b/IcH/jzdxSwI/dRp2ZrEG+UFDNyZ
ChTdgW1k+WWLrTKaw5S+mmtM9sLQ7Ia5dL+ZyE7tFIEGzuCSdAbbOIkygw+rhLy9
BO0rsTbXRuErRpUJgwKc56sFrvBL2pm4Rx+4IV29jhXdyJ70MUvRAINcHLESeBcO
uI5dqapScRf/EnVYP2Zso6i2FLep5hoC0reBq2UQ5Y95Lv0cpMCbHQ1xqdcm9pI3
ZvLDpVyGpp75Eoxlt1Ubiv6ijsEnTaM3cI+Q5rRWt8g3JKP7yYT7HGbJ3fb0cWhq
bNNISs+XN67lnyU1Mx3c2pjyb+szJZ0o4OGbYNAqsquItl4B0RQc3fUBMlCUlYI=
=+2Hj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.
When merging with wireless-drivers this pull request has a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve that just drop the changes from commit cf52c8a776 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a38 (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.
Major changes:
qtnfmac
* support WPA3 SAE and OWE in AP mode
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
mt76
* MT7663 support for the MT7615 driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cap_mask1 isn't protected by field_select and not listed among RW
fields, but it is required to be written to properly initialize ports
in IB virtualization mode.
Link: https://lore.kernel.org/linux-rdma/88bab94d2fd72f3145835b4518bc63dda587add6.camel@redhat.com
Fixes: ab118da4c1 ("net/mlx5: Don't write read-only fields in MODIFY_HCA_VPORT_CONTEXT command")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.
On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.
The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
- When emitting a oneshot pulse, instead of being told when to emit it,
the switch just does it "now" and tells you later what time it was,
via the PTPSYNCTS register. [ Incidentally, this is the same register
that the slave uses to collect the ext_ts timestamp from, too. ]
- On the sync slave, there is no interrupt mechanism on reception of a
new extts, and no FIFO to buffer them, because in the foreseen use
case, software is in control of both the master and the slave pins,
so it "knows" when there's something to collect.
These 2 problems mean that:
- We don't support (at least yet) the quirky oneshot mode exposed by
the hardware, just normal periodic output.
- We abuse the hardware a little bit when we expose generic extts.
Because there's no interrupt mechanism, we need to poll at double the
frequency we expect to receive a pulse. Currently that means a
non-configurable "twice a second".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.
Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the PTP_CLK pin starts toggling only at a time higher than the
current PTP clock, this helper from the time-aware shaper code comes in
handy here as well. We'll use it to transform generic user input for the
perout request into valid input for the sja1105 hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields configure the destination and source MAC address that the
switch will put in the Ethernet frames sent towards the CPU port that
contain RX timestamps for PTP.
These fields do not enable the feature itself, that is configured via
SEND_META0 and SEND_META1 in the General Params table.
The implication of this patch is that the AVB Params table will always
be present in the static config. Which doesn't really hurt.
This is needed because in a future patch, we will add another field from
this table, CAS_MASTER, for configuring the PTP_CLK pin function. That
can be configured irrespective of whether RX timestamping is enabled or
not, so always having this table present is going to simplify things a
bit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch found a lack of appropriate whitespace after certain keywords
as per the style guide. Add it in.
Signed-off-by: Logan Magee <mageelog@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify mv3310_reset() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify aqr107_wait_reset_complete() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify bcm84881_wait_init() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c: In function nicvf_sq_free_used_descs:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c:1182:12: warning:
variable tail set but not used [-Wunused-but-set-variable]
It's not used since commit 4863dea3fab01("net: Adding support for Cavium ThunderX network controller"),
so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed7903 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only attach macsec to ethernet devices.
Syzbot was able to trigger a KMSAN warning in macsec_handle_frame
by attaching to a phonet device.
Macvlan has a similar check in macvlan_port_create.
v1->v2
- fix commit message typo
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out setting GPHY 10M to new helper rtl8168g_enable_gphy_10m.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-03-21
Implement basic support for the devlink interface in the ice driver.
Additionally pave some necessary changes for adding a devlink region that
exposes the NVM contents.
This series first contains 5 patches for enabling and implementing full NVM
read access via the ETHTOOL_GEEPROM interface. This includes some cleanup of
endian-types, a new function for reading from the NVM and Shadow RAM as a flat
addressable space, a function to calculate the available flash size during
load, and a change to how some of the NVM version fields are stored in the
ice_nvm_info structure.
Following this is 3 patches for implementing devlink support. First, one patch
which implements the basic framework and introduces the ice_devlink.c file.
Second, a patch to implement basic .info_get support. Finally, a patch which
reads the device PBA identifier and reports it as the `board.id` value in the
.info_get response.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes wrapper fn()s around mutex_init/lock/unlock.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed MODULE_VERSION and fixed MODULE_AUTHOR.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MTU sized receive buffers it is not expected to have CQE_RX
with multiple receive buffer pointers. But since same physcial link
is shared by PF and it's VFs, the max receive packet configured
at link could be morethan MTU. Hence there is a chance of receiving
plts morethan MTU which then gets DMA'ed into multiple buffers
and notified in a single CQE_RX. This patch treats such pkts as errors
and frees up receive buffers pointers back to hardware.
Also on the transmit side this patch sets SMQ MAXLEN to max value to avoid
HW length errors for the packets whose size > MTU, eg due to path MTU.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF shares physical link with PF. Admin function (AF) sends
notification to PF whenever a link change event happens. PF
has to forward the same notification to each of the enabled VF.
PF traps START/STOP_RX messages sent by VF to AF to keep track of
VF's enabled/disabled state.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ethtool support for VF devices for
- Driver stats, Tx/Rx perqueue stats
- Set/show Rx/Tx queue count
- Set/show Rx/Tx ring sizes
- Set/show IRQ coalescing parameters
- RSS configuration etc
It's the PF which owns the interface, hence VF
cannot display underlying CGX interface stats.
Except for this rest ethtool support reuses PF's
APIs.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On OcteonTx2 silicon there two two types VFs, VFs that share the
physical link with their parent SR-IOV PF and the VFs which work
in pairs using internal HW loopback channels (LBK). Except for the
underlying Rx/Tx channel mapping from netdev functionality perspective
they are almost identical. This patch adds netdev driver support
for these VFs.
Unlike it's parent PF a VF cannot directly communicate with admin
function (AF) and it has to go through PF for the same. The mailbox
communication with AF works like 'VF <=> PF <=> AF'.
Also functionality wise VF and PF are identical, hence to avoid code
duplication PF driver's APIs are resued here for HW initialization,
packet handling etc etc ie almost everything. For VF driver to compile
as module exported few of the existing PF driver APIs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleanups all resources attached
to that VF.
Also handled IRQs triggered when master enable bit is cleared
or set for VFs. This handler just clears the transaction pending
ie TRPEND bit.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
