common->init_done flag should set after basic initialization. Hence,
moving init_done flag at end of rsi_91x_init().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.
Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System is unable to wake-up through magic-packet in secured connections.
Because key descriptor is getting corrupted and firmware is unable to
decrypt the magic packet. Fixed the issue by properly preparing it
before sending it to firmware.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Radio capabilities packet is not prepared properly for 40MHZ case,
ppe_ack_rate is a two byte variable which is initialized wrongly,
hence we are unable to connect, resolved by assigning it properly.
Signed-off-by: Ganapathi Raju <ganapathi.kondraju@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mwifiex firmware inserts only Microsoft information element
Allow other vendor specific IEs to pass from userspace
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is using boolean variables to maintain vairous status
information of adapter. These status variables are accessed by
multiple threads and there is a possibility of a race. To avoid
this, convert these variables to a set of bitops flags, to be
operated atomically.
Below variables of mwifiex_adapter are converted to bitop flags:
surprise_removed
is_cmd_timedout
is_suspended
is_hs_configured
hs_enabling
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver must ensure that whenever it holds a pointer to the list
entry mwifiex_rx_reorder_tbl, it must protect the same with
rx_reorder_tbl_lock. At present there are many places where
driver does not ensure this. To cover all cases, spinlocks in
below funcions are moved out and made sure that the caller will
hold the spinlock:
mwifiex_11n_dispatch_pkt_until_start_win()
mwifiex_11n_scan_and_dispatch()
mwifiex_del_rx_reorder_entry()
mwifiex_11n_get_rx_reorder_tbl()
mwifiex_11n_find_last_seq_num()
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At present driver spinlock protects iteration of list
rx_reorder_tbl_ptr with rx_reorder_tbl_lock. To protect the
individual items in this list, it uses rx_pkt_lock. But, we can
use a single rx_reorder_tbl_lock for both purposes. This patch
replaces rx_pkt_lock by rx_reorder_tbl_lock.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements following ethtool stats fields for netvsc:
cpu<n>_tx/rx_packets/bytes
cpu<n>_vf_tx/rx_packets/bytes
Corresponding per-cpu counters already exist in current code. Exposing
these counters will help troubleshooting performance issues.
for_each_present_cpu() was used instead of for_each_possible_cpu().
for_each_possible_cpu() would create very long and useless output.
It is still being used for internal buffer, but not for ethtool
output.
There could be an overflow if cpu was added between ethtool
call netvsc_get_sset_count() and netvsc_get_ethtool_stats() and
netvsc_get_strings(). (still safe if cpu was removed)
ethtool makes these three function calls separately.
As long as we use ethtool, I can't see any clean solution.
Currently and in foreseeable short term, Hyper-V doesn't support
cpu hot-plug. Plus, ethtool is for admin use. Unlikely the admin
would perform such combo operations.
Changes in v2:
- Remove cpp style comment
- Resubmit after freeze
Changes in v3:
- Reimplemented with kvmalloc instead of alloc_percpu
Changes in v4:
- Fixed inconsistent array size
- Use kvmalloc_array instead of kvmalloc
Signed-off-by: Yidong Ren <yidren@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlte1NUTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8Z0zB/9CkuxbUOB8QsoorZ6NwoVcK4wNZNhN
SRB8BpJpZn+Bye5hxKvMXU3yeoZj5xIR4mopLiiKM/pp3y3yqk3uhh971SQmAhfa
ULv+leBiCaFatXgYQTngOi6Xg6faJvu6ZYKUzvNPT1gW40HQTYUCCJwdgvlCbGLs
AVa04gV6o5lSolCboEjeKLnsW9ByHBBkLaOOZCixt+VfS76gO29fYJmplz7WC9pW
Udw2KiQBSz/D5iMUoYxb9KiMAa5OL9dJfHfy4jIdsEMekBUj66KjzbFOBq90c1Pg
PVEABATxFTplL1He+PzkJLu15csnhH0VSurUenkoOfdMkbu1LCmdwd4S
=053y
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.18-20180730' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-07-30
this is a pull request of one patch for net/master.
The patch by Anton Vasilyev and the Linux Driver Verification project
fixes a memory leak in the ems_usb driver's disconnect function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only code refactoring as all call sites of
ath10k_htt_tx_alloc_msdu_id() take the same lock it can be moved into the
id_get function and the assertion dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables netlen, orig_buf, orig_len, dropped and stats are assigned values
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'netlen' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_buf' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_len' set but not used [-Wunused-but-set-variable]
warning: variable 'dropped' set but not used [-Wunused-but-set-variable]
warning: variable 'stats' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer rf is being assigned but is never used hence it is redundant
and can be removed.
Cleans up two clang warnings:
warning: variable 'rf' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointers dev and noa are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'noa' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.
Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.
Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
Tested on QCA9984 with firmware ver 10.4-3.6-00104
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes a recently added checkpatch warning:
wmi-tlv.c:2703: open brace '{' following function definitions go on the next line
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Extended Page Access is a 16-bit register, so change the page
parameter of vsc85xx_phy_page_set to a u16.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.
Current state:
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of cn23xx_dump_iq_regs.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 11M as tx rate for CCK protection control frames
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce mac80211 rts threshold handler in order to add frame
protection support to mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set MFP_CAPABLE bit in hw flag capabilities exported by the driver
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fall back to software encryption for hw unsupported ciphers in order
to enable 802.11w
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve more in the existing code by reusing dma_zalloc_coherent instead
of dma_alloc_coherent with __GFP_ZERO or superfluous zeroing buffer.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
-Saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbW7KLAAoJEEg/ir3gV/o+YZ8H/2D4Ogav0zxQaNnw4ASYPpVA
luW1tvGUyk3C+fgbZO7tp/DETGJKbSodSMV9ZasEFFuHPft37mQaEIZf2rq58DvT
Q6vaaewyRCB6SzIGYjCZWtLI0aE5QtwMWDRbRBlRyQ0zUV6wr26W3WWWM2SpCJGK
zSuAF3Np0dEPTzBB566CY0nhYpsBiBXm2QJcgySL2WIx1nwQ6X8MJxjErhgQV+2L
1wVT6YTm1K2cdx9LsORt3FB/mFTQcOJCpl88AyhBB+pc7+i6pBtBp95tcqD8wmtF
dnMBmR+JzT108VxvcBnpwCxuVI7lLCcAs9hYITTGzUbo6rqT8xXV2HQ1KwU17Ow=
=tJj8
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-27 (Vxlan updates)
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing MTU, RTNL is held so use rtnl_dereference
instead of rcu_dereference.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems it was missed while adding for first net dev in dual-emac mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlta2oUTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8SWrCADJyQjWSWZaHHpHJeD1kUStgDEG5lYJ
e3rgrCEz4CVqGz5/wfsRCiuch14APjyn+xiHxjd+wCOES0wEg0viPIe40NlY28w7
SGvIogYRC27PoIXGQClasFG2Y/MEyaKChVGXkMfgkLs/zoHvd22zkxx/0l6lIAK5
CGCj8wTM/ZPh7Fn0tbn35E12j7yoHsTIv5YN463/XZJ7qVUDm7JW0siyXxhw4yP9
W18CcjInMds7YyUvs/PMMKnSgqOmGFdBpaaAkuqHcJgk0buI52XJRVihnea8y0V1
aQya6U8NWVUM1PEN6gefhOIye1w9HapnIyS79m5gmRPm8zXxwwOBRLy2
=YwFQ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.19-20180727' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2018-01-16
this is a pull request for net-next/master consisting of 38 patches.
Dan Murphy's patch fixes the path to a file in the comment of the CAN
Error Message Frame Mask structure.
A patch by Colin Ian King fixes a typo in the cc770 driver.
The next patch is by me an sorts the Kconfigand Makefile entries of the
CAN-USB driver subdir alphabetically.
The patch by Jakob Unterwurzacher adds support for the UCAN USB-CAN
adapter.
YueHaibing's patch replaces a open coded skb_put()+memset() by
skb_put_zero() in the CAN-dev infrastructure.
Zhu Yi provides a patch to enable multi-queue CAN devices.
Three patches by Luc Van Oostenryck fix the return value of several
driver's xmit function, I contribute a patch for the a fourth driver.
Fabio Estevam's patch switches the flexcan driver to SPDX identifier.
Two patches by Jia-Ju Bai replace the mdelay() by a usleep_range() in
the sja1000 drivers.
The next 6 patches are by Anssi Hannula and refactor the xilinx CAN
driver and add support for the xilinx CAN FD core.
A patch by Gustavo A. R. Silva adds fallthrough annotation to the
peak_usb driver.
5 patches by Stephane Grosjean for the peak CANFD driver do some
cleanups and provide more improvements for further firmware releases.
The remaining 13 patches are by Jimmy Assarsson and the first clean up
the kvaser_usb driver, so that the later patches add support for the
Kvaser USB hydra family.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_set_gft_event_id_cm_hdr.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac8390 driver defines its own variants of memcpy_fromio() and
memcpy_toio(), using similar implementations, but different function
signatures.
Remove the custom definitions of memcpy_fromio() and memcpy_toio(), and
adjust all callers to the standard signatures.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
With system having a small memory (around 256MB), the state "cannot
allocate memory to refill with new buffer" is reach pretty quickly.
By this patch we changed buffer allocation method to a better handling of
this use case by avoiding memory allocation issues.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory: extract from a larger patch]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the checksum offload feature is not set, then there is no point to
check the status of the hardware.
[gregory: extract from a larger patch]
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of trying to allocate the exact amount of memory for each
descriptor use a page for each of them, it allows to simplify the
allocation management and increase the performance of the driver.
Based on the work of Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve the diagnostic in case of error, make the distinction
between refill error and skb allocation error. Also make the information
available through the ethtool state.
Based on the work of Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
