Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the shared memory command parsing into common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad40 ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
C step NICs should use the latest FW (currently B step).
Correct the condition to make C step NICs advanced its default FW name
to the latest one.
Also rename _next_ to b_or_c to avoid confusion.
Fixes: 5da083d192 ("iwlwifi: add support for 9000 HW B-step NICs")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.
This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we create a regulatory domain out of an MCC
notification, we need to make sure that all the channels
in the rule have the exact same properties.
The current code mixes channel 36 and 40 although 36 can be
a control channel with HT40+ (36, 40) whereas 40 can't be
a control channel with HT40+ since (40, 44) is invalid.
Because of that, cfg80211 would allow to connect in 40MHz
to APs that are configured to channel 40 HT40+ and that made
our firmware assert.
Fix this by checking the bandwidth flags before taking the
decision if the rule should be split.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299 partly.
Fixes: af45a9003f ("iwlwifi: create regdomain from mcc_update_cmd response")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware now adds a new DWORD for the MLME offload's
capability even on firmware versions that don't support
it.
Add the TLV bit to avoid getting the print:
capa flags index 3 larger than supported by driver.
This fixes the bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=196195
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.
On A000 devices series, the IV is always added by the
device.
Fix this.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.
The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.
Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.
Fix that.
Fixes: 0c4cb7314d ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Cc: <stable@vger.kernel.org>
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.
However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.
In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we now support 8 device families, move their configuration
files into a new subdirectory "cfg".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This structure represents V2, V1 has the three last fields missing.
Rename it to be more accurate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the first frame on a given TID is received with seqno 0 and needed
to be retransmitted, we erroneously drop it because the deduplication
data is initialized to zero, and then comparing
if (unlikely(ieee80211_has_retry(hdr->frame_control) &&
dup_data->last_seq[tid] == hdr->seq_ctrl &&
dup_data->last_sub_frame[tid] >= sub_frame_idx))
return true;
will return in iwl_mvm_is_dup() since last_sub_frame is also set to
zero, and sub_frame_idx is usually zero since this only covers the
relatively rare case of A-MSDU.
Fix this by initializing the last_seq array to 0xffff, which is an
impossible value for hdr->seq_ctrl to have here because the lower
four bits are the fragment number, and fragments aren't handled in
this code but go to mac80211 instead.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.
Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.
While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
