Some fixes for 4.16, only for iwlwifi and brcmfmac this time. All
pretty small.
iwlwifi
* fix an issue with the multicast queue
* fix IGTK handling
* fix some missing return value checks
* add support for a HW workaround for issues on some platforms
* a couple of fixes for channel-switch
* a few fixes for the aggregation handling code
brcmfmac
* drop Inter-Access Point Protocol packets by default
* fix check for ISO3166 regulatory code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatiw3AAoJEG4XJFUm622bU7IH/0sIrhxJw+RJhTFQhRIx+WdN
XPWCb1bUXMwb3+4a+Z3cPuLsKHsv4TJTXtglSvZtihpasr6zALNeoZCb6md5mHz8
lLRWmMsyPQqnVy7mC7CO7qY5u8M6cZFvJgmn3pU8TAcok2r0skFiKCjqhY6A5ZUM
V6dlmjld08i5Y8xGlFPFQwCK9NFNoe2YK5k7U5GeY+0PXK9koT7H7amXcYSnU+Nl
Vrv/MZCGsOYa5E93IhPYkGRBasKqnLcS8+Rf+0zJl1eZuumyMr1+eqgaF1gVRC8w
rTvGyHUMv5OXxw6UHItHlQbW+Wgypdo1qRCfsxsAWOj6W5L1uj258CgSiMcwp1o=
=YWna
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.16
Some fixes for 4.16, only for iwlwifi and brcmfmac this time. All
pretty small.
iwlwifi
* fix an issue with the multicast queue
* fix IGTK handling
* fix some missing return value checks
* add support for a HW workaround for issues on some platforms
* a couple of fixes for channel-switch
* a few fixes for the aggregation handling code
brcmfmac
* drop Inter-Access Point Protocol packets by default
* fix check for ISO3166 regulatory code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
request_firmware_cache() will ensure the firmware is available on resume
from suspend if on reboot the device retains the firmware.
This optimization is in place given otherwise on reboot we have to
reload the firmware, the opmization saves us about max 1s, minimum 10ms.
Cantabile has reported back this fixes his woes with both suspend and
hibernation.
Reported-by: Cantabile <cantabile.desu@gmail.com>
Tested-by: Cantabile <cantabile.desu@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When switching mac80211 to use QoS NDP, it turned out that
ath9k_htc is somehow broken by this, e.g. see
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060.
Fix this by using the new mac80211 flag to go back to the
old, incorrect, behaviour for this driver.
Fixes: 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing")
Reported-by: Ben Caradoc-Davies <ben@transient.nz>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the wmediumd to the net's wmediumd when the radio gets created.
Radios created after HWSIM_CMD_REGISTER don't currently get their
data->wmediumd set and the userspace would need to reconnect to
netlink to be able to call HWSIM_CMD_REGISTER again.
Alternatively I think data->netgroup and data->wmedium could be
replaced with a pointer to hwsim_net.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When destroying a net namespace, all hwsim interfaces, which are not
created in default namespace are deleted. But the async deletion of the
interfaces could last longer than the actual destruction of the
namespace, which results to an use after free bug. Therefore use
synchronous deletion in this case.
Fixes: 100cb9ff40 ("mac80211_hwsim: Allow managing radios from non-initial namespaces")
Reported-by: syzbot+70ce058e01259de7bb1d@syzkaller.appspotmail.com
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
OR'ing in 0x40 before a memcpy() to overwrite the value doesn't
do much good - flip the order of operations are reported and
tested by Jouni.
Fixes: cb1a5bae56 ("mac80211_hwsim: add permanent mac address option for new radios")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.
Fixes: 657308f73e ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When immediate quiet bit is set in CSA, the entire channel is blocked
by the firmware. It is expected that all the MACs will evacuate the
channel and the phy will be eventually either moved or removed.
Currently, the phy context is just unreferenced and thus, the quiet
bit is kept set and it will be impossible to TX on this phy, if we
will need to reuse it in the future. This can be seen when doing a
channel switch with mode=1 (quiet) twice from channel X to Y and then
back to channel X.
Fix that, by moving the phy context to a default channel when not
referenced anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.
While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.
Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.
Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.
Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Testing brcmfmac with more recent firmwares resulted in AP interfaces
not working in some specific setups. Debugging resulted in discovering
support for IAPP in Broadcom's firmwares.
Older firmwares were only generating 802.11f frames. Newer ones like:
1) 10.10 (TOB) (r663589)
2) 10.10.122.20 (r683106)
for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames
in the Tx path by performing a STA disassociation.
This obsoleted standard and its implementation is something that:
1) Most people don't need / want to use
2) Can allow local DoS attacks
3) Breaks AP interfaces in some specific bridge setups
To solve issues it can cause this commit modifies brcmfmac to drop IAPP
packets. If affects:
1) Rx path: driver won't be sending these unwanted packets up.
2) Tx path: driver will reject packets that would trigger STA
disassociation perfromed by a firmware (possible local DoS attack).
It appears there are some Broadcom's clients/users who care about this
feature despite the drawbacks. They can switch it on using a new module
param.
This change results in only two more comparisons (check for module param
and check for Ethernet packet length) for 99.9% of packets. Its overhead
should be very minimal.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations. We need to set a bit in the phy
configuration to indicate that to the FW. To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware. And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.
Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.
Found by smatch:
.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.
The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.
To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.
Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.
This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.
Fixes: 50f08edf98 ("ath9k: Switch to using mac80211 intermediate software queues.")
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.
Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At present driver gets chan_type by referring to
IEEE80211_HT_PARAM_CHA_SEC_OFFSET, in ASSOC response. Sometimes
AP shows IEEE80211_HT_PARAM_CHA_SEC_OFFSET as above/below in
assoc response, even if the association is done on HT20 channel
only. So, it will be accurate to get econdary channel offset from
firmware.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IEEE80211_CHAN_NO_HT40PLUS and IEEE80211_CHAN_NO_HT40PLUS channel
flags tell if HT40 operation is allowed on a channel or not.
This patch ensures ht_capability information is modified
accordingly so that we don't end up creating a HT40 connection
when it's not allowed for current regulatory domain.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit bcc920e8f0.
Drivers gets hardware info and updates ht_cap field of
wiphy->bands during initialization. Once updated during init,
ht_cap must not be modified as it reflects the capability
supported by hardwawre. Above patch tries to modify the ht_cap
field and this results in wrongly advertising capabilities during
association.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
High bits of antenna number are reserved in hardware spec,
using low 4 bits represent supported antenna.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Curretly, RX packet processing is done sequencially. To improve
the efficiency, RX skb queue is introduced.
Here, while preparing RX URB skb is allocated and used
for RX buffer. When rx done handler is called, enqueue the skb
to rx_q and set the thread event.
RX thread is modified to dequeue packets from skb queue and
process further.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently 2 RX control blocks are allocated by default.
If wifi alone mode is used rx control block 2 is unusable.
So, changes are done accordingly in all places to use
RX control blocks dynamically based on coex mode check.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RX packets are handled in interrupt context in SDIO
interface. To improve the efficiency of processing RX packets,
RX thread and RX skb queues are introduced.
When the packet is read from device, driver prepares skb, add to
RX queue and trigger RX thread event. RX thread processes the
packets from RX queue.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Queue number is correctly updated for BT traffic. Also, kzalloc
instead of kmalloc is used for Rx packet allocation.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Operating mode determines the support for other protocols.
This is made as module parameter for better usage.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT frames are passed through coex and hal modules to BUS.
After firmware is loaded, based on the operating mode CARD
READY frame comes for each protocol. When BT card ready is
received, BT attach is called.
Protocol operations are exchanged between the modules
at initialization time.
Build flag CONFIG_RSI_COEX is introduced to enable coex support
if CONFIG_BT_RSIHCI is enabled. Coex operations are valid if
coex mode is greater than 1 only.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With BT support, driver has to handle two streams of data
(i.e. wlan and BT). Actual coex implementation is in firmware.
Coex module just schedule the packets to firmware by taking them
from the corresponding paths.
Structures for module and protocol operations are introduced for
this purpose. Protocol operations structure is global structure
which can be shared among different modules. Move initialization
of coex and operating mode values to rsi_91x_init().
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The common parameters used by wlan and bt modules are add
to a new header file "rsi_91x.h" defined in 'include/net'
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx bluetooth endpoint shall be added in further patches. Rx control
block is introduced here to handle Rx packets properly. Separate
function is written to initialize the RX control blocks.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Apparently the hardware does not perform CCMP PN validation so
let mac80211 take care of possible replay attacks in sw.
Moreover indicate ICV and MIC had been stripped setting corresponding
bits in ieee80211_rx_status.
The fix has been validated using 4.2.1 and 4.1.3 tests from the WiFi
Alliance vulnerability detection tool.
Fixes: c869f77d6a ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: David Park <david.park@hitemengineering.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove mt7601u_dev parameter from mt7601u_mcu_msg_alloc signature since
dev pointer is never used in routine body
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute unnecessary len variable in mt76x2_eeprom_load() with
MT7662_EEPROM_SIZE macro since len is used just to store eeprom
default size.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the following sparse warning in mt7601u_efuse_physical_size_check:
- drivers/net/wireless/mediatek/mt7601u/eeprom.c:77:27: warning:
Variable length array is used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add capability to select tx/rx antennas. Possible values are:
- 1: to use only the first antenna
- 2: to use only the second antenna
- 3: to use both of them
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76_init_stream_cap utility routine to set ht/vht sta capabilities
related to number of streams currently used by the device
(it will be used by mac80211 set_antenna callback)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize available_antennas related info in wiphy data structure
according to antenna_mask field; antenna_mask info is initialized
in device specific code and will be used in mac80211 {set,get}_antenna
callbacks
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.
iwlwifi
* fix a bogus warning when freeing a TFD
* fix severe throughput problem with 9000 series
* fix for a bug that caused queue hangs in certain situations
* fix for an issue with IBSS
* fix an issue with rate-scaling in AP-mode
* fix Channel Switch Announcement (CSA) issues with count 0 and 1
* some firmware debugging fixes
* remov a wrong error message when removing keys
* fix a firmware sysassert most usually triggered in IBSS
* a couple of fixes on multicast queues
* a fix with CCMP 256
rtlwifi
* fix loss of signal for rtl8723be
brcmfmac
* add possibility to obtain firmware error
* fix P2P_DEVICE ethernet address generation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaoVCFAAoJEG4XJFUm622bRiQIAKJ9HmZQwda8Y7Ypj/y2YIJr
Rqmd+PSjfD+FNT33Ue+x/LPCfM2SnFQdnL61kqOSIgOCDS+uwwe8mDVa+DtaT+Dd
sU5ftjVjBXuYiqs2XW0n8dPszFftc7omCNVAeAJcBISqrqKkXUi3Bg47jK02kV6E
AAGvyJwxIMr187nFaC8N55cas0At7Mbbsvh0YRNjxnoqKOmC3NpJZPskv3C/gvUs
ADJkFPUwImqE9+BwoEguAGcqV8hLVVnoXf87Ro4L1SrFl11gJSiifq/FqwXHXm8E
YyJNo6lGdaw5uuX2T9wW6QfBghMoncE/tmwgLKdLyjyV8H2c6iEMKMygZIN0eTI=
=HvdQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo:
====================
wireless-drivers fixes for 4.16
Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.
iwlwifi
* fix a bogus warning when freeing a TFD
* fix severe throughput problem with 9000 series
* fix for a bug that caused queue hangs in certain situations
* fix for an issue with IBSS
* fix an issue with rate-scaling in AP-mode
* fix Channel Switch Announcement (CSA) issues with count 0 and 1
* some firmware debugging fixes
* remov a wrong error message when removing keys
* fix a firmware sysassert most usually triggered in IBSS
* a couple of fixes on multicast queues
* a fix with CCMP 256
rtlwifi
* fix loss of signal for rtl8723be
brcmfmac
* add possibility to obtain firmware error
* fix P2P_DEVICE ethernet address generation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.
Cc: stable@vger.kernel.org # 3.10.y
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The feature module needs to evaluate the actual firmware error return
upon a control command. This adds a flag to struct brcmf_if that the
caller can set. This flag is checked to determine the error code that
needs to be returned.
Fixes: b69c1df472 ("brcmfmac: separate firmware errors from i/o errors")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These pernet_operations allocate and destroy IDA identifier,
and these actions are synchronized by IDA subsystem locks.
Exit method removes mac80211_hwsim_data enteries from the lists,
and this is synchronized by hwsim_radio_lock with the rest
parallel pernet_operations. Also it queues destroy_radio()
work, and these work already may be executed in parallel
with any pernet_operations (as it's a work :). So, we may
mark these pernet_operations as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
hwsim_netgroup counter is declarated as int, and it is incremented
every time a new net is created. After sizeof(int) net are created,
it will overflow, and different net namespaces will have the same
identifier. This patch fixes the problem by introducing IDA instead
of int counter. IDA guarantees, all the net namespaces have the uniq
identifier.
Note, that after we do ida_simple_remove() in hwsim_exit_net(),
and we destroy the ID, later there may be executed destroy_radio()
from the workqueue. But destroy_radio() does not use the ID, so it's OK.
Out of bounds of this patch, just as a report to wireless subsystem
maintainer, destroy_radio() increaments hwsim_radios_generation
without hwsim_radio_lock, so this may need one more patch to fix.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'default false' should be 'default n', though they happen to have the
same effect here, due to undefined symbols ('false' in this case)
evaluating to n in a tristate sense.
Remove the default instead of changing it. bool and tristate symbols
implicitly default to n.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the scheduler config command, the meaning of tid == 0xf was intended
to indicate the configuration is for management frames. However,
tid == 0xf was also used for the multicast queue that was meant only
for multicast data frames, which resulted with the FW not encrypting
multicast data frames.
As multicast frames do not have a QoS header, fix this by setting
tid == 0, to indicate that this is a data queue and not management
one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
